MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series

MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
MEC Auto-Mate Assembly Manual
   For MEC 9000G/GN and 8567 Grabber Series 
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
Thank you…

 We really appreciate your support of our product
 line. But our commitment to you hardly ends here.
  We won't be satisfied until your new MEC Auto-
Mate exceeds your expectations. . . year after year.

 We encourage you to take your time as you begin
 to use your new MEC Auto-Mate. Carefully review
  this manual to learn the operational features and
          considerations for safe operation.
Your MEC Auto-Mate is a machine that if used to its
 capability will speed the process of reloading, and
  for those with physical impairments, will allow you
 to once again be able to load your own shot shells.
   But like any machine you need to thoroughly
        understand it to get the most out of it.


  That's where we come in again. If you have any
 questions, comments, or suggestions we want to
          hear from you. Give us a call at,
                    800-797-4632
         8AM - 4PM CST Monday-Friday.




                                                        2
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
Contents
   NOTE: If you are upgrading an 8567 Grabber Series machine, turn to Page 15 Step 16
   and contact the factory for the items listed.
   Section 1. Safety Information. – Page 4
   Section 2.
   Section 1. Safety
              Remove Information
                       Parts From- Your
                                   Page MEC
                                        4   9000G/GN or 8567 Grabber. – Page 6
   Section 2. Removal of Factory Manual Operational Parts For MEC 9000G/GN or
   Section 3. Install “Quick-Link” Parts to Your 9000G/GN or 8567 Grabber. – Page 11
              8567 Grabber - Page 6
   Section
   Section 4. Assemble Your
           3. Quick-Link     MEC Auto-Mate.
                         Kit Installation - Page –10Page 19
   Section 5. InstallationYour
           4. Assemble     of Left
                               MEC Side Loader Brace
                                     Auto-Mate.      – Page
                                                - Page 16 21

           5. Installation
   Section 6.              of Left
              Auto-Mate Fuse       Side Truss Rod
                                Replacement       - Page
                                              – Page 24 18
   Section 6. Auto-Mate Fuse Replacement - Page 19




Section 1.
                                                                                        3
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
Safety Information
General
The MEC Auto-Mate is a unique product in that it is designed to work in conjunction with equipment
and reloading components designed and manufactured by Mayville Engineering Company, Inc. It is
therefore of up-most importance to read, fully understand, and strictly follow the operation, user, and
safety information for ALL the equipment and reloading components that you will be using in the
reloading process.

Millions of men and women reload ammunition as a hobby, or because the cost savings allow them to
enjoy shooting more often. You should always reload so that the safest and most accurate loads on
the shooting line will be yours, and always remember that to become or to continue to be a safe
reloader, you must be careful at all times.
Checking powder and shot charges with a reliable scale is a must, and will disclose if you have any
variations in weights. Adhering to loads recommended by the powder manufacturer is a must.
Always wear safety glasses!

On your machine and in this operator’s manual safety labels and statements contain the words
DANGER for the most serious hazards and CAUTION to call attention to safety messages.


       DANGER                              CAUTION

Electrical


   (1) To avoid electrical shock, which can cause severe personal, injury or death do not cut or
       remove the round grounding prong from the plug. Machine must be grounded at all times. Do
       not remove warning tag from power cord. Do not use a two-prong adapter. Do not use an
       extension cord.
       Electrical Grounding Instructions - This machine is equipped with a three-prong
       (grounding) plug for protection against possible shock hazards. If you encounter a
       two prong receptacle, contact a qualified electrician and have the two-prong wall
       receptacle replaced with a properly grounded three-prong wall receptacle in
       accordance with the National Electrical Code.
       Machine is designed to operate on a separate 110 to 120 volt. 15 amp.. 60 cycle line.

   (2) Avoid contact with energized circuits.




                                                                                                      4
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
Safety Information
Electrical – Cont’d

   (3) Do not depend on motor control devices (switches, etc.) to prevent unexpected motor starting.
       Always disconnect power source before working on or adjusting machine.

   (4) Protect the power cable: don't let it touch sharp objects, hot surfaces, oil, grease, or chemicals.
       Do not kink the power cable.




              DANGER
   (5) DO NOT USE THIS EQUIPMENT IN AN AREA WHERE EXPLOSIVE VAPORS ARE
       PRESENT.



              CAUTION
   (6) DISCONNECT POWER SUPPLY BEFORE SERVICING, OR MAKING ANY ADJUSTMENTS.


Mechanical

              DANGER
   (1) KEEPS HANDS AND FINGERS CLEAR OF ALL MOVING PARTS.


   (2) Your machine is quite heavy. Be sure to use your MEC Auto-Mate on a structurally sound table
       or bench.




                                                                                                         5
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
Section 2.

 RemovalQuick-Link
        Of  Factory      Parts
                         Manual  Installation
                                     Operational
        REMOVAL OF FACTORY MANUAL OPERATION PARTS Parts

                          TOOLS REQUIRED
                          (2) 7/16” OPEN END WRENCHES
                          (1) 1/2” OPEN END WRENCH
                          (1) 5/32” HEX WRENCH




                          STEP 1
                          RAISE CHARGE BAR AND MEASURE
                          ASSEMBLY. REMOVE POWDER AND
                          SHOT BOTTLES.




                            STEP 2
                            REMOVE BOTH SHOT AND POWDER
                            DROP TUBES AND SET ASIDE.




                                                          6
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
STEP 3
                    ASSEMBLYTO
 DEPRESS HANDLE ASSEMBLY       TO
     BOTTOM OF
 THE BOTTOM    OF LOADING
                  LOADING STROKE.
                           STROKE.
 TIGHTEN
 USING (2) MIDDLE  BOLT TO KEEP
           7/16” WRENCHES   TIGHTEN
 TURRETBOLT
 MIDDLE   ASSEMBLY   IN THE
               TO KEEP      DOWN
                        TURRET  AS-
 POSITION.
 SEMBLY  IN THE DOWN POSITION.




 STEP 4
 WITH A ½” END WRENCH, REMOVE
 THE PIVOT BLOCK BOLT AND SET
 ASIDE.




STEP 5
REMOVE
REMOVE MEASURE   ASSEMBLY
        CHARGE BAR  AND    AS
SHOWN
MEASUREAND SET ASIDE.
         ASSEMBLY  AND SET
ASIDE.




                                      7
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
STEP 6
USING
LOOSEN (2)MIDDLE
           7/16” WRENCHES
                   BOLT AND LOOSEN
                             RETURN
MIDDLE
TURRETBOLT     AND RETURN
          ASSEMBLY    TO THETURRET
                              FULL UP
ASSEMBLY
POSITION.   TO  THE FULL  UP POSI-
TION.
PULL DROP TUBE HOLDER
PULL  DROP UP
ASSEMBLY     TUBE  HOLDER
                 AND LAY TOASSEM-
                             THE
BLY UPITAND
SIDE.         LAYNECESSARY
         IS NOT   TO THE SIDE.TO
                               IT UN-
                                  IS
NOT NECESSARY
COUPLE             TO UN-COUPLE
          THE ATTACHED    LINKAGES.
THE ATTACHED LINKAGES.




STEP
 STEP77
USING
 WITH (2) 7/16”END
       A 7/16”  WRENCHES
                   WRENCHREMOVE
                           REMOVE
THE REAR   LINKAGE  BOLT ASSEMBLY
 THE REAR LINKAGE BOLT ASSEMBLY
AND
 ANDKEEP
      KEEPFOR
            FORPOSSIBLE
                 POSSIBLEFUTURE
                          FUTURE
USE.
 USE.




STEP
 STEP8 8
USING
  WITH(2)
        A 7/16”
          7/16” WRENCHES
                END WRENCH  REMOVE
                               REMOVE
THE LOCK   NUT  AND SET  ASIDE.
  THE LOCK NUT AND SET ASIDE.
NOTE
  NOTEAPPROXIMATE
        APPROXIMATE   ADJUSTMENT
                         ADJUSTMENT
POSITION  OF  THE  CRIMP
  POSITION OF THE CRIMP   DIEDIE
                              CAM.
                                 CAM.
YOU WILL
  YOU     NEED
       WILL  NEEDTOTO
                    READJUST
                       READJUST THE
                                  THE
CAM
  CAMFOLLOWING
       FOLLOWING  THE
                    THEAUTO-MATE
                          AUTO-MATE
“QUICK-LINK”
  “QUICK-LINK”PARTS  INSTALLATION.
                 PARTS  INSTALLATION.




                                        8
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
Actuator Arm
    STEP 9
►   REMOVE THE HANDLE ASSEMBLY.
    STEP
    USE BOTH9 HANDS TO SPREAD THE
    IF YOU HAVE
    FORKS   OF THETHE LARGEAND
                     HANDLE  CAPACITY
                                 PULL
    PRIMER
    TOWARDFEEDFRONTYOUOFWILL HAVE TO
                         MACHINE.
    REMOVE
    SAVE THETHE    #8965IN
               HANDLE    ACTUATOR  ARM
                           THE EVENT
    THAT YOU
    USING      WANT
           A 5/32” HEXTO  CONVERT
                       WRENCH   ANDTHE
    LOADER
    SET      BACK
        ASIDE.  NOTETOTHE
                       MANUAL
                           POSITION OF
    OPERATION.
    THE  SCREW IN RELATIONSHIP TO
    THE SLOT.




    STEP
     STEP10
          10
    USING
     WITH (2) 7/16”END
           A 7/16”  WRENCHES
                       WRENCHREMOVE
                               REMOVE
    THE
     THETOP
         TOPLINKAGE
               LINKAGEBOLT AND
                        BOLT   SET
                             AND SET
    ASIDE.
     ASIDE.

    SAVE
     SAVETHE
          THERIGHT  AND
                RIGHT ANDLEFT
                          LEFTLINKAGE
                                LINKAGE
    PIECES
     PIECESININTHE
                THEEVENT
                    EVENTTHAT
                           THATYOU
                                 YOU
    WANT TO   CONVERT  THE  LOADER
     WANT TO CONVERT THE LOADER
    BACK
     BACKTO
          TOMANUAL
               MANUALOPERATION
                       OPERATION.




    THIS IS THE WAY THE TOP SECTION
    OF YOUR LOADER SHOULD APPEAR
    PRIOR TO THE INSTALLATION OF THE
    MEC AUTO-MATE “QUICK-LINK” KIT.




                                          9
MEC Auto-Mate Assembly Manual - For MEC 9000G/GN and 8567 Grabber Series
Quick-Link Kit Installation
INSTALLATION OF MEC AUTO-MATE “QUICK-LINK” KIT


                        STEP 1
                        PREPARE FOR INSTALLATION BY
                        LAYING OUT THE “QUICK-LINK”
                        PARTS.




                        STEP 2
                        LOOKING FROM THE BACK OF THE
                        LOADER, PLACE THE TOP LINKAGE
                        BOLT THROUGH THE LEFT HAND
                        LINK AND SLIDE BOLT THRU HOLE
                        PROVIDED IN TOP OF COLUMN AND
                        THEN THRU RIGHT HAND LINK.




                       STEP
                       STEP 33
                       USING
                        USING(2) 7/16”OF
                               A SET   WRENCHES
                                         7/16” END TIGHTEN
                       THE  TOP LINKAGE
                        WRENCHES          BOLT
                                     TIGHTEN    ASSEMBLY
                                               THE TOP
                       IMPORTANT!
                        LINKAGE BOLT ASSEMBLY THE
                                     ONLY  TIGHTEN
                       TOP  LINKAGE ONLY
                        IMPORTANT!    BOLT NUT  ENOUGH
                                            TIGHTEN  THE
                       TO  BRING  ALL OF THE  PARTS
                        TOP LINKAGE BOLT NUT ENOUGH TO
                       TOGETHER.
                        BRING ALL OFTHE ACTUATION
                                       THE  PARTS ARMS
                       MUST   MOVE  FREELY.
                        TOGETHER. THE ACTUATION ARMS
                        MUST MOVE FREELY UP AND DOWN.




                                                             10
STEP 4
               ON RIGHT SIDE OF LOADER
               ASSEMBLE THE FORWARD LINK
               BOLT, LINK STRAP, AND SPACING
               WASHER AS SHOWN.




             STEP 5
             ON LEFT SIDE OF LOADER ADD ¼”
             SPACING WASHER, LINK STRAP,
             CAM PLATE AND FORWARD LINKAGE
             BOLT NUT.
             IMPORTANT! MAKE SURE THE
             THREADED HOLE IN THE LINK STRAP
             IS AWAY FROM THE LOADER.




                STEP 6
                USING(2)
                WITH   (2)7/16”
                           7/16”END
                                 WRENCHES
                                    WRENCHES TIGHTEN
                THE FORWARD      LINKAGE  BOLT
                TIGHTEN THE FORWARD LINKAGE
                ASSEMBLY.
                BOLT         IMPORTANT! ONLY
                      ASSEMBLY.
                TIGHTEN    THE
                IMPORTANT! ONLY FORWARD   LINKAGE
                                    TIGHTEN   THE
                BOLT NUT ENOUGH
                FORWARD     LINKAGETO   BRING
                                      BOLT NUTALL
                OF THE PARTS
                ENOUGH           TOGETHER.
                           TO BRING  ALL OF THE
                LINK STRAPS
                PARTS  TOGETHER.MUST THE
                                     MOVE   FREELY
                                         LINK
                UP AND DOWN.
                STRAPS           USINGFREELY
                         MUST MOVE     A 5/32” HEX
                                               UP
                WRENCH
                AND  DOWN. TIGHTEN THE CAM IN THE
                APPROXIMATE POSITION LIKE IT
                WAS ON YOUR HANDLE. YOU MAY
Section 3.      HAVE TO ADJUST THE POSITION
                WHEN YOU BEGIN RELOADING.




                                                       11
STEP 7
  RE-ATTACH THE
  RE-ATTACH THE INDEXING
                  INDEXINGACTUAT-
  ACTUATION
  ING       BRACKET.
      BRACKET. IF YOU ALSO HAVE THE
  LARGE CAPACITY PRIMER FEED, RE-
  ATTACH THE ACTUATOR ARM AT THIS
  TIME.




STEP 8
ADD
ADD THE
    THE REAR
         REAR LINK
                LINK BOLT
                     BOLT AND
                          NUT TIGHT-
                              AND
EN USING (2) 7/16” WRENCHES.
TIGHTEN.
IMPORTANT! ONLY
             ONLY TIGHTEN
                   TIGHTEN THE
                            THE REAR
LINKAGE BOLT ENOUGH
REAR LINKAGE   BOLT NUT TO BRING ALL
                          ENOUGH
OF THE PARTS   TOGETHER.
TO BRING ALL OF THE PARTS
TOGETHER.




STEP 9
MOVE THE DROP TUBE HOLDER
ASSEMBLY BACK INTO POSITION.




                                       12
STEP 10
DEPRESS LINKAGE   ASSEMBLY TO
          HANDLE ASSEMBLY       TO
THE BOTTOM OF LOADING STROKE.
WHILE HOLDING
TIGHTEN MIDDLEITBOLT
                 DOWN, TO TIGHT-
                           KEEP
TURRET ASSEMBLY
EN MIDDLE          IN THE
           BOLT USING       DOWN
                        (2) 7/16”
POSITION.
WRENCHES TO KEEP TURRET AS-
SEMBLY IN THE DOWN POSITION.




        STEP 11
             11
        FROM
        ALIGN THE
              THE FRONT  OF THEAND
                  PIVOT BLOCK   RELOADER
        ALIGN
        CHARGETHE PIVOT
                BAR     BLOCK AND
                     ASSEMBLY  ANDCHARGE
        BAR ASSEMBLY
        ATTACH        ANDPIVOT
                WITH THE  ATTACH  WITH THE
                               BLOCK
        PIVOT
        BOLT. BLOCK BOLT.




 STEP 12
 WITH A ½” END WRENCH TIGHTEN
 PIVOT BLOCK BOLT SECURELY.




                                        13
STEP
 STEP 13
      13
 CAREFULLY
 CAREFULLY LOOSEN
            LOOSEN THE
                    THE MIDDLE
                        MIDDLE
 BOLT  AND RETURN  TURRET
 BOLT AND RETURN TURRET ASSEMBLY
 ASSEMBLY  TOUP
 TO THE FULL  THE FULL UP CAUTION
                POSITION.
 POSITION.
 SHOULD BE TAKEN TO NOT ALLOW
 THE UNIT TO COME UP TOO QUICKLY.




 STEP 14
 ADD POWDER AND SHOT DROP
 TUBES.




STEP 15
LOWER CHARGE BAR ASSEMBLY.




                                    14
FROM
                       THIS ISTHE SIDE/BACK
                               WHAT          VIEW OF
                                     THE FINISHED
                       THE  RELOADER   THIS
                       ASSEMBLY SHOULD LOOK IS WHAT THE
                                                 LIKE.
                       FINISHED  ASSEMBLY SHOULD
                       CONGRATULATIONS,     YOU ARELOOK
                       LIKE.
                       ALMOST READY TO GO! YOU ARE
                             CONGRATULATIONS,
                       ALMOST READY TO GO!




                       STEP 16
                            16
                       WITH A 7/16”
                       INSTALL THE END
                                     RIGHTWRENCH,  INSTALL
                                           HAND LOADER
                       THE LOADER
                       SUPPORT       SUPPORT
                                  BRACKET      BRACKET.
                                            USING THE PRO-
                       USE THE
                       VIDED 1/4“PROVIDED   ¼” NUT
                                  NUT AND BOLT.    AND WITH
                                                 START
                       BOLT.
                       THE   START
                           TOP  BOLTWITH   THE TOP
                                       AS SHOWN     BOLT
                                                 HERE  AND
                       AS SHOWN
                       FINGER      HERE. TIGHTEN
                               TIGHTEN.
               ►       SECURELY. IF YOU ARE CONVERTING
                       IMPORTANT:
                       IMPORTANT:
                       A GRABBER 8567IF YOU ARE
                                          CALL THE FACTORY
                       CONVERTING     A GRABBER
                       AND REQUEST THE RIGHT HAND 8567
                       CALL THE
                       TRUSS  ROD FACTORY        REQUEST
                                    #9130P9 AND WING
                       THE RIGHT   HAND
                       THUMB SCREW #9105. TRUSS ROD
Bolt/Nut               #9130P9


                      STEP
                   STEP 17 17
                   WITHCOMPLETE
                        A 7/16” ENDTHE  INSTALLATION OF
                                     WRENCH,
   Bolt/Nut            THE LOADER
                   COMPLETE          SUPPORT BRACKET
                               THE INSTALLATION    OF
                       BY SECURING
                   THE LOADER         THE BOTTOM
                                 SUPPORT   BRACKETOF  BYTHE
                       BRACKET
                   SECURING   THETO  LOADER.
                                   BOTTOM    OFTIGHTEN
                       BOTHTO
                   BRACKET    BOLTS  SECURELY
                                LOADER.   TIGHTENUSING (2)
                       7/16” WRENCHES.
                   SECURELY.
                       NOTE:  MAKE   CERTAIN
                                          THISTHIS
           ►




                   NOTE: MAKE   CERTAIN
                       CONNECTION
                   CONNECTION         IS MADE
                                 IS MADE       ON THE
                                          ON THE
                   BACKSIDE   OF THE
                       BACKSIDE    OF INDEXER   SIDE SIDE
                                       THE INDEXER
                   PLATE  AS SHOWN.
                       PLATE  AS SHOWN.

                   IMPORTANT: FOLLOW
                       IMPORTANT: FOLLOW
                   INSTRUCTIONS FOR FOR
                       INSTRUCTIONS 8567 8567
                                         GRABBER
                                              GRABBER
                   RIGHT HAND TRUSS ROD  #9130P9
                       RIGHT HAND TRUSS ROD #9130P9
                   ASSEMBLY.
                       ASSEMBLY.




                                                              15
Auto-Mate Assembly
          STEP 1
          SLIDE YOUR
          SLIDE YOUR RELOADER
                      AUTO-MATEINTO
                                 INTO
          POSITION ON THE
          POSITION ON  THE TOP
                           TOP OF
                               OF THE
                                  THE
          DRIVE BASE.
          DRIVE BASE.
          WITH THE
          WITH THE PROVIDED
                   PROVIDED THUMB
                             THUMB
          SCREWS, SECURE THE LEFT
          SCREWS,  SECURE  THE LEFT SIDE
                                    SIDE
          OF THE LOADER TO THE DRIVE
          OF THE LOADER  TO THE DRIVE
          BASE.




          STEP 2
          LOOSEN
          PUSH    THE
                THE    (2) THUMB
                    RIGHT         SCREWS
                            SIDE HOLD DOWN
          AND PUSH THE
          CLAMPING       RIGHT
                     STRIP      SIDE
                            TO THE   HOLD
                                   LEFT UNTIL
          DOWN
          IT     CLAMPING
             RESTS AGAINSTSTRIP   TO THE
                             THE LOADER
          LEFT UNTIL IT RESTS AGAINST THE
          BASE.
          LOADER BASE.
          SECURE   CLAMPING STRIP TIGHTLY
          SECURE
          WITH THECLAMPING
                    PROVIDEDSTRIP
                               THUMBTIGHTLY
          SCREWS.
          WITH PROVIDED THUMB SCREWS.
          TIGHTEN ALLEN SCREW USING 5/32”
          HEX WRENCH.




         STEP 3
         WITH A ½” END WRENCH, REMOVE
         THE NY-LOCK NUT FROM THE
         ACTUATION WHEEL PIVOT POINT.
         ATTACH THE BOTTOM END OF THE
         PULL ROD AND TIGHTEN THE LOCK
         NUT.




                                                16
STEP 4
  STEP 4
  REMOVETHE
  THREAD   THELOCK
                BOLTNUT
                      FROMONTHE
                             TO THE
  PIVOT  BRACKET   AND  THREAD
  TOP OF THE PULL ROD FOLLOWED  THEBY
  PIVOT  BRACKET   ONTO  THE PULL
  THE PIVOT BRACKET. THE HOLES IN
  ROD.PIVOT
  THE   RE-POSITION
             BRACKETTHE   PIVOTBE
                       SHOULD
  BRACKET   BETWEEN    THE LINKS.IN
  SLIGHTLY HIGHER THAN THOSE
  THE LINKS.
  THE  HOLESAINSLIGHT
                 THE PIVOT  BRACKET
                       AMOUNT   OF
  SHOULD   LINE UP  WITH THE  HOLES
  DOWNWARD PRESSURE IS REQUIRED
  IN THE
  TO     LINKS.
     SLIDE      SLIDETHROUGH
           THE BOLT    THE BOLTTHE
  THROUGH    THE  LINKAGE  AND PIVOT
  LINKS AND THE PIVOT BRACKET.
  BRACKET. THE BOLT SHOULD SLIDE
  THROUGH FREELY.




  STEP 5
  USING (2) 7/16” END WRENCHES
  TIGHTEN THE LINKAGE BOLT
  ASSEMBLY.

  IMPORTANT: ONLY TIGHTEN THE
  LINKAGE BOLT ENOUGH TO BRING
  ALL PARTS TOGETHER.
  BOLT SHOULD PIVOT FREELY.




STEP 6
INSTALL THE SPENT PRIMER BIN
UNDER THE AUTO-MATE BASE
FRAME IN LOCATION SHOWN,




                                        17
Installation  Of Left Truss Rod
                   INSTALLATION OF LEFT TRUSS ROD

Bolt/Nut
                              STEP
                              STEP 11
                              INSERT
                              INSERT THE
                                      BOLTBOLT THROUGH
                                            THRU        THE
                                                 TOP HOLE IN TRUSS
                              HOLE  IN THE
                              ROD AND      MOUNTING
                                        SLIDE        BRACKET
                                              THRU HOLE IN BACK SIDE
                              AND  THEN
                              OF THE     THROUGH
                                      MOUNTING    THE TOPON
                                                 BRACKET  HOLE
                                                             THE LEFT
           ►

                              IN THE TRUSS  ROD ON THE LEFT
                              SIDE OF RELOADER. FINGER TIGHTEN AT
                              SIDE
                              THIS OF  RELOADER AND FINGER
                                   POINT.
                              TIGHTEN NUT. YOU MAY FIND IT
                              EASIER TO INSERT BY TIPPING THE
                              MEASURE ASSEMBLY BACK.




                            STEP 2
                            USING THE PROVIDED “T” BOLT,
                            INSTALL LOWER TRUSS ROD TO THE
                            PROVIDED MOUNTING HOLE AT THE
                            LEFT REAR OF THE AUTO-MATE
                            DRIVE BASE AND SECURELY
                            TIGHTEN.




                                STEP
                                STEP 33
                                USING
                                USING (2)
                                       TWO7/16” END
                                             7/16”   WRENCHES,
                                                   END WRENCHES,
                                SECURELY   TIGHTENTHE
                                SECURLY TIGHTEN      THEBOLT
                                                         BOLTAND
                                                             AND
                                NUT HOLDING    THE  UPPER TRUSS
                                NUT HOLDING THE UPPER TRUSS
                                ROD
                                ROD TO
                                    TO THE
                                        THE RELOADER
                                              RELOADER MOUNTING
                                                        MOUNTING
                                BRACKET.
                                BRACKET.




                                                                        18
Auto-Mate Fuse Replacement
     Fuse Replacement

              STEP 1
              REMOVE POWER CORD!




             STEP 2
             TO EXPOSE FUSE.
             WITH A SMALL STANDARD SCREW
             DRIVER PUSH IN WHILE TURNING
             COUNTER CLOCKWISE.




              STEP 3
              REMOVE FUSE FROM FUSE HOLDER
              AND REPLACE WITH A FUSE THAT
              MATCHES FACTORY
              SPECIFICATIONS. ( SEE BELOW)


              3AG – 250V .75 AMP FAST ACTING

              NOTE: LESSER QUALITY FUSES MAY
              BLOW AT LOWER THAN RATED
              VALUE. IF YOU CAN NOT LOCATE
              FUSES THAT MEET THESE SPECS,
              CONTACT MEC FOR REPLACEMENT
              FUSES.

                                               19
MEC AUTO-MATE
   PART #                      DESCRIPTION     Mayville Engineering Company
     9102                      Power Cord      An Employee Owned Company
     9128                      .75 Amp Fuse             715 South Street
     9129                      1 Amp Fuse              Mayville, WI 53050
     9135                      Magnet
     9113                      Hex Flange Nut (for magnet)      P
     9104                      Thumb Screw (Round)
   9130P6                      Right Side Hold Down Bracket
     9134                      Pull Rod Assembly
0113H1544                      Carriage Bolt
     9114                      Nylon Lock Nut (Carriage Bolt)
     6466                      Lock Nut (Carriage Bolt)
     8661                      Truss Rod (right side for 9000 series machine)
     685F                      Bolt
     460A                      Lock Nut
  9130P10                      Truss Rod (left side)
     9105                      Thumb Screw (Wing)
   9130P9                      Truss Rod (right side for 8567 series machine)
     9100                      Primer Catcher
     8546                      Linkage Assembly



   PART #                      Accessory Items

      9149                     Links Kit (Converts another 9000 or 8567 series machine to operate on the MEC Auto-Mate)
      9156                     Large Push Buttons
      9162                     Quick Disconnect Pin




                            Mayville Engineering Company, Inc.
                               An Employee Owned Company
                                      715 South Street
                                     Mayville, WI 53050
                         Ph: (800) 797-4632     Fax (920) 387-5802
               website: www.mecreloaders.com • email:reloaders@mayvl.com

Form No. 9145 (09/07) Rev. 1

                                                                                                                      20
Next part ... Cancel