Test Report PRIMERGY RX2540 M1 with CentOS

Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01




Test Report
PRIMERGY RX2540 M1 with CentOS




                                                        Content
                                                         Release Overview                                        2
                                                         Warranty conditions                                     3
                                                         Disclaimer of liability                                 3
                                                         Support                                                 3
                                                         References                                              3
                                                         Test configuration conf01                               4
                                                         Test configuration conf02                               4
                                                         Test configuration conf03                               4
                                                         PRIMERGY RX2540 M1 with CentOS 7.1 (x86_64)             5
                                                         PRIMERGY RX2540 M1 with CentOS 7.0 (x86_64)             7
                                                         PRIMERGY RX2540 M1 with CentOS 6.6 (x86)               11
                                                         PRIMERGY RX2540 M1 with CentOS 6.6 (x86_64)            13
                                                         PRIMERGY RX2540 M1 with CentOS 6.5 (x86)               15
                                                         PRIMERGY RX2540 M1 with CentOS 6.5 (x86_64)            17




Page 1 of 19                                                                                    www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


Release Overview
This paper comprises the test reports of the PRIMERGY RX2540 M1 with the free operating system CentOS versions and platforms as described as
follows.




                                    Conf01. SAS Array Controller Card   Conf02. SAS Array Controller Card   Conf03. SAS Array Controller Card
                   OS
                                             PRAID EP420i                        PRAID EP400i                        PRAID CP400i

     CentOS 7.1(x86_64)                      YES(Note 1,6,7)                    YES(Note 1,6,7)                      YES(Note 1,7)

     CentOS 7.0(x86_64)                      YES(Note 1,6,7)                     YES(Note 1,7)                       YES(Note 1,7)

     CentOS 6.6(x86)                          YES(Note 1,7)                     YES(Note 1,6,7)                     YES(Note 1,6,7)

     CentOS 6.6(x86_64)                       YES(Note 1,7)                     YES(Note 1,6,7)                     YES(Note 1,6,7)

     CentOS 6.5(x86)                         YES(Note 1,6,7)                     YES(Note 1,7)                      YES(Note 1,6,7)

     CentOS 6.5(x86_64)                      YES(Note 1,6,7)                     YES(Note 1,7)                      YES(Note 1,6,7)




                           Legend
                           Yes: Installable       No: Not installable         -: Unknown
                           Note: Check that ServerView Agents are only installed on target operating system.
                           Explanatory notes
                           1. Requires LAN driver
                           2. Install in TEXT mode
                           3. Requires SAS controller driver and LAN driver
                           4. Requires SAS controller driver
                           5. Requires SATA controller driver
                           6. Can be installed logically
                           7. Other




Page 2 of 19                                                                                                             www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


Warranty conditions
Fujitsu is providing all work for customer’s convenience only under the conditions of Fujitsu’s general Warranty Disclaimer for Community and
Regional Linux: ftp://ftp.ts.fujitsu.com/community-linux/Community_Linux_Warranty_Disclaimer.pdf

The information presented in the CentOS test reports is strictly based on results obtained in a test environment prepared by Fujitsu and is not
intended to guarantee operation of a free operating system in the customer’s user environment or to encourage use of a free operating system.
Information contained in this document may be subject to change without notice.

Disclaimer of liability
Due to many hardware and software components involved, the possibility of system crashes, data loss or other negative consequences for your
system cannot be excluded. Fujitsu shall not bear responsibility for any loss that the customer may incur as a result of having installed and/or
used a free operating system based on the verification data presented here.
Fujitsu Customer Service is unable to accept inquiries or provide support relating to the use of PRIMERGY on free operating systems.
Customers are therefore requested to take full responsibility for the installation and use of such free operating systems.
Hardware repair and maintenance shall be limited to machines operating under the duly supported OS environment.

Support
Support is only provided by the CentOS community. Please refer to the Warranty Disclaimer for details on Warranty and Liability of the
downloaded ServerView agents and ServerView RAID Manager.

References
Fujitsu Linux Internet:                       http://ts.fujitsu.com/linux
Community and Regional Linux FTP site:        ftp://ftp.ts.fujitsu.com/community-linux
Warranty Disclaimer:                          ftp://ftp.ts.fujitsu.com/community-linux/Community_Linux_Warranty_Disclaimer.pdf
Fujitsu “Drivers & Downloads” site:           http://support.ts.fujitsu.com/com/support/downloads.html
OS compatibility matrix:                      http://docs.ts.fujitsu.com/dl.aspx?id=d4ebd846-aa0c-478b-8f58-4cfbf3230473




Page 3 of 19                                                                                                             www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


Test configuration conf01

Hardware environment:
  PRIMERGY RX2540 M1
  ■ CPU : Intel Xeon E5-2603 v3 1.60GHz/6core/15MB x2
  ■ Memory : 64GB
  ■ NIC : Onboard 1000BASE-T x2 or 1000BASE-T x4
  ■ HDD : SATA 500GB x3
  ■ External storage : DVD drive

Device driver [Driver name]:
  ■ LAN : Emulex Corporation OneConnect NIC (Skyhawk) (rev 10) [be2net]
  ■ VGA : Matrox Electronics Systems Ltd. MGA G200e [Pilot] ServerEngines (SEP1) (rev 05)
  ■ RAID : LSI Logic / Symbios Logic MegaRAID SAS-3 3108 [Invader] (rev 02) [megaraid_sas]




Test configuration conf02

Hardware environment:
  PRIMERGY RX2540 M1
  ■ CPU : Intel Xeon E5-2603 v3 1.60GHz/6core/15MB x1
  ■ Memory : 16GB
  ■ NIC : Onboard 1000BASE-T x2 (CentOS 6.5 x86),
                   1000BASE-T x2 or 1000BASE-T x4 (CentOS 6.5 x86_64, CentOS 7.0)
  ■ HDD : SATA 500GB x2
  ■ External storage : DVD drive

Device driver [Driver name]:
  ■ LAN : Emulex Corporation OneConnect NIC (Skyhawk) (rev 10) [be2net]
  ■ VGA : Matrox Electronics Systems Ltd. MGA G200e [Pilot] ServerEngines (SEP1) (rev 05)
  ■ RAID : LSI Logic / Symbios Logic MegaRAID SAS-3 3108 [Invader] (rev 02) [megaraid_sas]




Test configuration conf03

Hardware environment:
  PRIMERGY RX2540 M1
  ■ CPU : Intel Xeon E5-2667 v3 3.20GHz/8core/20MB x2
  ■ Memory : 16GB
  ■ NIC : Onboard 1000BASE-T x2 or 1000BASE-T x4
  ■ HDD : SATA 500GB x2
  ■ External storage : DVD drive

Device driver [Driver name]:
  ■ LAN : Emulex Corporation OneConnect NIC (Skyhawk) (rev 10) [be2net]
  ■ VGA : Matrox Electronics Systems Ltd. MGA G200e [Pilot] ServerEngines (SEP1) (rev 05)
  ■ RAID : LSI Logic / Symbios Logic MegaRAID SAS-3 3008 [Fury] (rev 02) [megaraid_sas]




Page 4 of 19                                                                                 www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


PRIMERGY RX2540 M1 with CentOS 7.1 (x86_64)

Installation and Operational Checking Results with conf03
      PRIMERGY RX2540 M1 CentOS 7.1 (x86_64) 3.10.0-229.el7.x86_64
 No.        Item checked                                                                                        Result
 1         Is there HDD/RAID driver support? (OS standard or special)                                           OS Standard
 2         Is there LAN driver support? (OS standard or special)                                                Special(*1)
 3         Is installation possible in the verification machine?                                                OK(*2)
 4         Is reboot possible after installation, and does the OS start correctly?                              OK
 5         Can the GUI be used?                                                                                 OK
 6         Can the keyboard be used?                                                                            OK
 7         Can the mouse be used?                                                                               OK
 8         After OS start, is login as a root user possible?                                                    OK
 9         Can a USB stick disk be used?                                                                        -
 10        Can the CD/DVD-ROM drive be used?                                                                    OK
 11        When logged in as a root user, does the “shutdown -h now” command perform shutdown?                  OK
 12        Confirmation of write to local disk (write, delete, etc.)                                            OK
 13        Are the values set during installation displayed correctly (ip command)?                             OK
 14        Can a ping be sent from the verification machine to another PC?                                      OK
 15        Can a ping be sent to the verification machine from another PC?                                      OK
 16        Can a network utility (ip,nmcli,nmtui, etc.) be used to change the network configuration?            OK
 17        Can the web service (httpd) be used?                                                                 OK
 18        Can the ftp service be used?                                                                         OK
 19        Can the nfs service be used?                                                                         OK
 20        Can the Network data transfer (nfs) be used?                                                         OK
 21        Result of disk array management tool [ServerViewRAID] installation?                                  OK
 22        Result of server management software [ ServerView agents ] installation?                             -
 23        Does the OS run even if the HDD on one side is removed? * Remove HDD when stopped, and then start    -(*3)
 24        Is login as a root user possible if the HDD on one side is removed?                                  -(*3)
 25        Can the touch command be used to write if the HDD on one side is removed?                            -(*3)
 26        Does the OS start when restart is performed if the HDD on one side is removed?                       -(*3)
 27        Is the RAID configuration rebuilt when the RAID on one side is put back?                             -(*3)
 28        Is reboot possible and does the OS start correctly after RAID configuration rebuilding ends?         -(*3)
 29        Is login as a root user possible after RAID configuration rebuilding ends?                           -(*3)
 30        48 hours stress test of CPU, HDD and network using cpubench, bonnie and phoronix test suite          -(*3)
*1 The driver can be obtained from the following site.
  URL: http://support.ts.fujitsu.com/download/index.asp
      Select as follows
       Product selection(manually search) : Fujitsu Server PRIMERGY -> PRIMERGY RXxxx
       -> PRIMERGY RX2540 M1 -> Red Hat Enterprise Linux -> Red Hat Enterprise Linux 7(x86_64)
       -> LAN -> Emulex XE104/XE102 -> RHDUP driver package be2net 10.2.405.22-1 for RHEL7.1
     [Driver Information]
         Date : 06.03.2015
         Size : 0.11MB
         Version : 10.2.405.22-1-5
         Manufacturer : Fujitsu Technology Solutions

*2 Even if the USB ports is not used, disable the USB3.0 function.
    Select as follows
      BIOS menu : Advanced -> USB Configuration -> xHCI Mode -> Disabled
*3 Done with the corresponding Red Hat Enterprise Linux version.



Page 5 of 19                                                                                                   www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01



  ■ Installation procedure

     1.   After DVD boot, select [Install CentOS 7] and press Enter.
     2.   Follow usual procedure for remainder of install.
     3.   The relevant Server Management Software (ServerView) including manuals are located on the Fujitsu download site of the respective
          server for the corresponding Red Hat Enterprise Linux version.
          Reference: http://support.ts.fujitsu.com/com/support/downloads.html.




Page 6 of 19                                                                                                       www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


PRIMERGY RX2540 M1 with CentOS 7.0 (x86_64)

Installation and Operational Checking Results with conf02
      PRIMERGY RX2540 M1 CentOS 7.0 (x86_64) 3.10.0-123.el7.x86_64
 No.        Item checked                                                                                        Result
 1         Is there HDD/RAID driver support? (OS standard or special)                                           OS Standard
 2         Is there LAN driver support? (OS standard or special)                                                Special(*1)
 3         Is installation possible in the verification machine?                                                OK(*2)
 4         Is reboot possible after installation, and does the OS start correctly?                              OK
 5         Can the GUI be used?                                                                                 OK
 6         Can the keyboard be used?                                                                            OK
 7         Can the mouse be used?                                                                               OK
 8         After OS start, is login as a root user possible?                                                    OK
 9         Can a USB stick disk be used?                                                                        -
 10        Can the CD/DVD-ROM drive be used?                                                                    OK
 11        When logged in as a root user, does the “shutdown -h now” command perform shutdown?                  OK
 12        Confirmation of write to local disk (write, delete, etc.)                                            OK
 13        Are the values set during installation displayed correctly (ip command)?                             OK
 14        Can a ping be sent from the verification machine to another PC?                                      OK
 15        Can a ping be sent to the verification machine from another PC?                                      OK
 16        Can a network utility (ip,nmcli,nmtui, etc.) be used to change the network configuration?            OK
 17        Can the web service (httpd) be used?                                                                 OK
 18        Can the ftp service be used?                                                                         OK
 19        Can the nfs service be used?                                                                         OK
 20        Can the Network data transfer (nfs) be used?                                                         OK
 21        Result of disk array management tool [ServerViewRAID] installation?                                  OK
 22        Result of server management software [ ServerView agents ] installation?                             -
 23        Does the OS run even if the HDD on one side is removed? * Remove HDD when stopped, and then start    -(*3)
 24        Is login as a root user possible if the HDD on one side is removed?                                  -(*3)
 25        Can the touch command be used to write if the HDD on one side is removed?                            -(*3)
 26        Does the OS start when restart is performed if the HDD on one side is removed?                       -(*3)
 27        Is the RAID configuration rebuilt when the RAID on one side is put back?                             -(*3)
 28        Is reboot possible and does the OS start correctly after RAID configuration rebuilding ends?         -(*3)
 29        Is login as a root user possible after RAID configuration rebuilding ends?                           -(*3)
 30        48 hours stress test of CPU, HDD and network using cpubench, bonnie and phoronix test suite          -(*3)
*1 The driver can be obtained from the following site.
  URL: http://support.ts.fujitsu.com/download/index.asp
      Select as follows
       Product selection(manually search) : Fujitsu Server PRIMERGY -> PRIMERGY RXxxx
       -> PRIMERGY RX2540 M1 -> Red Hat Enterprise Linux -> Red Hat Enterprise Linux 7(x86_64)
       -> LAN -> Emulex XE104/XE102 -> RHDUP driver package be2net 10.2.405.22-1 for RHEL 7 GA
     [Driver Information]
         Date : 11.12.2014
         Size : 0.11MB
         Version : 10.2.405.22-1-0
         Manufacturer : Fujitsu Technology Solutions

*2 Even if the USB ports is not used, disable the USB3.0 function.
    Select as follows
      BIOS menu : Advanced -> USB Configuration -> xHCI Mode -> Disabled
*3 Done with the corresponding Red Hat Enterprise Linux version.



Page 7 of 19                                                                                                   www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01



  ■ Installation procedure

     1.   After DVD boot, select [Install CentOS 7] and press Enter.
     2.   Follow usual procedure for remainder of install.
     3.   The relevant Server Management Software (ServerView) including manuals are located on the Fujitsu download site of the respective
          server for the corresponding Red Hat Enterprise Linux version.
          Reference: http://support.ts.fujitsu.com/com/support/downloads.html.




Page 8 of 19                                                                                                       www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01




Installation and Operational Checking Results with conf03
      PRIMERGY RX2540 M1 CentOS 7.0 (x86_64) 3.10.0-123.el7.x86_64
 No.        Item checked                                                                                        Result
 1         Is there HDD/RAID driver support? (OS standard or special)                                           OS Standard
 2         Is there LAN driver support? (OS standard or special)                                                Special(*1)
 3         Is installation possible in the verification machine?                                                OK(*2)
 4         Is reboot possible after installation, and does the OS start correctly?                              OK
 5         Can the GUI be used?                                                                                 OK
 6         Can the keyboard be used?                                                                            OK
 7         Can the mouse be used?                                                                               OK
 8         After OS start, is login as a root user possible?                                                    OK
 9         Can a USB stick disk be used?                                                                        -
 10        Can the CD/DVD-ROM drive be used?                                                                    OK
 11        When logged in as a root user, does the “shutdown -h now” command perform shutdown?                  OK
 12        Confirmation of write to local disk (write, delete, etc.)                                            OK
 13        Are the values set during installation displayed correctly (ip command)?                             OK
 14        Can a ping be sent from the verification machine to another PC?                                      OK
 15        Can a ping be sent to the verification machine from another PC?                                      OK
 16        Can a network utility (ip,nmcli,nmtui, etc.) be used to change the network configuration?            OK
 17        Can the web service (httpd) be used?                                                                 OK
 18        Can the ftp service be used?                                                                         OK
 19        Can the nfs service be used?                                                                         OK
 20        Can the Network data transfer (nfs) be used?                                                         OK
 21        Result of disk array management tool [ServerViewRAID] installation?                                  OK
 22        Result of server management software [ ServerView agents ] installation?                             -
 23        Does the OS run even if the HDD on one side is removed? * Remove HDD when stopped, and then start    -(*3)
 24        Is login as a root user possible if the HDD on one side is removed?                                  -(*3)
 25        Can the touch command be used to write if the HDD on one side is removed?                            -(*3)
 26        Does the OS start when restart is performed if the HDD on one side is removed?                       -(*3)
 27        Is the RAID configuration rebuilt when the RAID on one side is put back?                             -(*3)
 28        Is reboot possible and does the OS start correctly after RAID configuration rebuilding ends?         -(*3)
 29        Is login as a root user possible after RAID configuration rebuilding ends?                           -(*3)
 30        48 hours stress test of CPU, HDD and network using cpubench, bonnie and phoronix test suite          -(*3)
*1 The driver can be obtained from the following site.
  URL: http://support.ts.fujitsu.com/download/index.asp
      Select as follows
       Product selection(manually search) : Fujitsu Server PRIMERGY -> PRIMERGY RXxxx
       -> PRIMERGY RX2540 M1 -> Red Hat Enterprise Linux -> Red Hat Enterprise Linux 7(x86_64)
       -> LAN -> Emulex XE104/XE102 -> RHDUP driver package be2net 10.2.405.22-1 for RHEL 7 GA
     [Driver Information]
         Date : 11.12.2014
         Size : 0.11MB
         Version : 10.2.405.22-1-0
         Manufacturer : Fujitsu Technology Solutions

*2 Even if the USB ports is not used, disable the USB3.0 function.
    Select as follows
      BIOS menu : Advanced -> USB Configuration -> xHCI Mode -> Disabled
*3 Done with the corresponding Red Hat Enterprise Linux version.




Page 9 of 19                                                                                                   www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


  ■ Installation procedure

     1.   After DVD boot, select [Install CentOS 7] and press Enter.
     2.   Follow usual procedure for remainder of install.
     3.   The relevant Server Management Software (ServerView) including manuals are located on the Fujitsu download site of the respective
          server for the corresponding Red Hat Enterprise Linux version.
          Reference: http://support.ts.fujitsu.com/com/support/downloads.html.




Page 10 of 19                                                                                                      www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


PRIMERGY RX2540 M1 with CentOS 6.6 (x86)

Installation and Operational Checking Results with conf01
      PRIMERGY RX2540 M1 CentOS 6.6 (x86) 2.6.32-504.el6.i686
 No.        Item checked                                                                                        Result
 1         Is there HDD/RAID driver support? (OS standard or special)                                           OS Standard
 2         Is there LAN driver support? (OS standard or special)                                                Special(*1)
 3         Is installation possible in the verification machine?                                                OK(*2)
 4         Is reboot possible after installation, and does the OS start correctly?                              OK
 5         Can the GUI be used?                                                                                 OK
 6         Can the keyboard be used?                                                                            OK
 7         Can the mouse be used?                                                                               OK
 8         After OS start, is login as a root user possible?                                                    OK
 9         Can a USB stick disk be used?                                                                        -
 10        Can the CD/DVD-ROM drive be used?                                                                    OK
 11        When logged in as a root user, does the “shutdown -h now” command perform shutdown?                  OK
 12        Confirmation of write to local disk (write, delete, etc.)                                            OK
 13        Are the values set during installation displayed correctly (ifconfig command)?                       OK
 14        Can a ping be sent from the verification machine to another PC?                                      OK
 15        Can a ping be sent to the verification machine from another PC?                                      OK
 16        Can a network utility (system-config-network*, etc.) be used to change the network configuration?    OK
 17        Can the web service (httpd) be used?                                                                 OK
 18        Can the ftp service be used?                                                                         OK
 19        Can the nfs service be used?                                                                         OK
 20        Can the Network data transfer (nfs) be used?                                                         OK
 21        Result of disk array management tool [ServerViewRAID] installation?                                  OK
 22        Result of server management software [ ServerView agents ] installation?                             OK
 23        Does the OS run even if the HDD on one side is removed? * Remove HDD when stopped, and then start    -(*3)
 24        Is login as a root user possible if the HDD on one side is removed?                                  -(*3)
 25        Can the touch command be used to write if the HDD on one side is removed?                            -(*3)
 26        Does the OS start when restart is performed if the HDD on one side is removed?                       -(*3)
 27        Is the RAID configuration rebuilt when the RAID on one side is put back?                             -(*3)
 28        Is reboot possible and does the OS start correctly after RAID configuration rebuilding ends?         -(*3)
 29        Is login as a root user possible after RAID configuration rebuilding ends?                           -(*3)
 30        48 hours stress test of CPU, HDD and network using cpubench, bonnie and phoronix test suite          -(*3)
*1 The driver can be obtained from the following site.
  URL: http://support.ts.fujitsu.com/download/index.asp
      Select as follows
       Product selection(manually search) : Fujitsu Server PRIMERGY -> PRIMERGY RXxxx
       -> PRIMERGY RX2540 M1 -> Red Hat Enterprise Linux -> Red Hat Enterprise Linux 6(x86)
       -> LAN -> Emulex XE104/XE102 -> RHDUP driver package be2net 10.2.405.22-1 for RHEL6.6
     [Driver Information]
         Date : 11.12.2014
         Size : 0.21MB
         Version : 10.2.405.22-1-0
         Manufacturer : Fujitsu Technology Solutions

*2 Even if the USB ports is not used, disable the USB3.0 function.
    Select as follows
      BIOS menu : Advanced -> USB Configuration -> xHCI Mode -> Disabled
*3 Done with the corresponding Red Hat Enterprise Linux version.



Page 11 of 19                                                                                                  www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01



  ■ Installation procedure

     1.   After DVD boot, select [Install or upgrade an existing system] and press Enter.
     2.   Follow usual procedure for remainder of install.
     3.   The relevant Server Management Software (ServerView) including manuals are located on the Fujitsu download site of the respective
          server for the corresponding Red Hat Enterprise Linux version.
          Reference: http://support.ts.fujitsu.com/com/support/downloads.html.




Page 12 of 19                                                                                                      www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


PRIMERGY RX2540 M1 with CentOS 6.6 (x86_64)

Installation and Operational Checking Results with conf01
      PRIMERGY RX2540 M1 CentOS 6.6 (x86_64) 2.6.32-504.el6.x86_64
 No.        Item checked                                                                                        Result
 1         Is there HDD/RAID driver support? (OS standard or special)                                           OS Standard
 2         Is there LAN driver support? (OS standard or special)                                                Special(*1)
 3         Is installation possible in the verification machine?                                                OK(*2)
 4         Is reboot possible after installation, and does the OS start correctly?                              OK
 5         Can the GUI be used?                                                                                 OK
 6         Can the keyboard be used?                                                                            OK
 7         Can the mouse be used?                                                                               OK
 8         After OS start, is login as a root user possible?                                                    OK
 9         Can a USB stick disk be used?                                                                        -
 10        Can the CD/DVD-ROM drive be used?                                                                    OK
 11        When logged in as a root user, does the “shutdown -h now” command perform shutdown?                  OK
 12        Confirmation of write to local disk (write, delete, etc.)                                            OK
 13        Are the values set during installation displayed correctly (ifconfig command)?                       OK
 14        Can a ping be sent from the verification machine to another PC?                                      OK
 15        Can a ping be sent to the verification machine from another PC?                                      OK
 16        Can a network utility (system-config-network*, etc.) be used to change the network configuration?    OK
 17        Can the web service (httpd) be used?                                                                 OK
 18        Can the ftp service be used?                                                                         OK
 19        Can the nfs service be used?                                                                         OK
 20        Can the Network data transfer (nfs) be used?                                                         OK
 21        Result of disk array management tool [ServerViewRAID] installation?                                  OK
 22        Result of server management software [ ServerView agents ] installation?                             OK
 23        Does the OS run even if the HDD on one side is removed? * Remove HDD when stopped, and then start    -(*3)
 24        Is login as a root user possible if the HDD on one side is removed?                                  -(*3)
 25        Can the touch command be used to write if the HDD on one side is removed?                            -(*3)
 26        Does the OS start when restart is performed if the HDD on one side is removed?                       -(*3)
 27        Is the RAID configuration rebuilt when the RAID on one side is put back?                             -(*3)
 28        Is reboot possible and does the OS start correctly after RAID configuration rebuilding ends?         -(*3)
 29        Is login as a root user possible after RAID configuration rebuilding ends?                           -(*3)
 30        48 hours stress test of CPU, HDD and network using cpubench, bonnie and phoronix test suite          -(*3)
*1 The driver can be obtained from the following site.
  URL: http://support.ts.fujitsu.com/download/index.asp
      Select as follows
       Product selection(manually search) : Fujitsu Server PRIMERGY -> PRIMERGY RXxxx
       -> PRIMERGY RX2540 M1 -> Red Hat Enterprise Linux -> Red Hat Enterprise Linux 6(x86_64)
       -> LAN -> Emulex XE104/XE102 -> RHDUP driver package be2net 10.2.405.22-1 for RHEL6.6
     [Driver Information]
         Date : 11.12.2014
         Size : 0.21MB
         Version : 10.2.405.22-1-0
         Manufacturer : Fujitsu Technology Solutions

*2 Even if the USB ports is not used, disable the USB3.0 function.
    Select as follows
      BIOS menu : Advanced -> USB Configuration -> xHCI Mode -> Disabled
*3 Done with the corresponding Red Hat Enterprise Linux version.



Page 13 of 19                                                                                                  www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01



  ■ Installation procedure

     1.   After DVD boot, select [Install or upgrade an existing system] and press Enter.
     2.   Follow usual procedure for remainder of install.
     3.   The relevant Server Management Software (ServerView) including manuals are located on the Fujitsu download site of the respective
          server for the corresponding Red Hat Enterprise Linux version.
          Reference: http://support.ts.fujitsu.com/com/support/downloads.html.




Page 14 of 19                                                                                                      www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


PRIMERGY RX2540 M1 with CentOS 6.5 (x86)

Installation and Operational Checking Results with conf02
      PRIMERGY RX2540 M1 CentOS 6.5 (x86) 2.6.32-431.el6.i686
 No.        Item checked                                                                                        Result
 1         Is there HDD/RAID driver support? (OS standard or special)                                           OS Standard
 2         Is there LAN driver support? (OS standard or special)                                                Special(*1)
 3         Is installation possible in the verification machine?                                                OK(*2)
 4         Is reboot possible after installation, and does the OS start correctly?                              OK
 5         Can the GUI be used?                                                                                 OK
 6         Can the keyboard be used?                                                                            OK
 7         Can the mouse be used?                                                                               OK
 8         After OS start, is login as a root user possible?                                                    OK
 9         Can a USB stick disk be used?                                                                        -
 10        Can the CD/DVD-ROM drive be used?                                                                    OK
 11        When logged in as a root user, does the “shutdown -h now” command perform shutdown?                  OK
 12        Confirmation of write to local disk (write, delete, etc.)                                            OK
 13        Are the values set during installation displayed correctly (ifconfig command)?                       OK
 14        Can a ping be sent from the verification machine to another PC?                                      OK
 15        Can a ping be sent to the verification machine from another PC?                                      OK
 16        Can a network utility (system-config-network*, etc.) be used to change the network configuration?    OK
 17        Can the web service (httpd) be used?                                                                 OK
 18        Can the ftp service be used?                                                                         OK
 19        Can the nfs service be used?                                                                         OK
 20        Can the Network data transfer (nfs) be used?                                                         OK
 21        Result of disk array management tool [ServerViewRAID] installation?                                  OK
 22        Result of server management software [ ServerView agents ] installation?                             OK
 23        Does the OS run even if the HDD on one side is removed? * Remove HDD when stopped, and then start    -(*3)
 24        Is login as a root user possible if the HDD on one side is removed?                                  -(*3)
 25        Can the touch command be used to write if the HDD on one side is removed?                            -(*3)
 26        Does the OS start when restart is performed if the HDD on one side is removed?                       -(*3)
 27        Is the RAID configuration rebuilt when the RAID on one side is put back?                             -(*3)
 28        Is reboot possible and does the OS start correctly after RAID configuration rebuilding ends?         -(*3)
 29        Is login as a root user possible after RAID configuration rebuilding ends?                           -(*3)
 30        48 hours stress test of CPU, HDD and network using cpubench, bonnie and phoronix test suite          -(*3)
*1 The driver can be obtained from the following site.
  URL: http://support.ts.fujitsu.com/download/index.asp
      Select as follows
       Product selection(manually search) : Fujitsu Server PRIMERGY -> PRIMERGY RXxxx
       -> PRIMERGY RX2540 M1 -> Red Hat Enterprise Linux -> Red Hat Enterprise Linux 6(x86)
       -> LAN -> Emulex XE104/XE102 -> RHDUP driver package be2net 10.2.346.0-1 for RHEL6.5
     [Driver Information]
         Date : 17.07.2014
         Size : 0.21MB
         Version : 10.2.346.0-1-0
         Manufacturer : Fujitsu Technology Solutions

*2 Even if the USB ports is not used, disable the USB3.0 function.
    Select as follows
      BIOS menu : Advanced -> USB Configuration -> xHCI Mode -> Disabled
*3 Done with the corresponding Red Hat Enterprise Linux version.



Page 15 of 19                                                                                                  www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01



  ■ Installation procedure

     1.   After DVD boot, select [Install or upgrade an existing system] and press Enter.
     2.   Follow usual procedure for remainder of install.
     3.   The relevant Server Management Software (ServerView) including manuals are located on the Fujitsu download site of the respective
          server for the corresponding Red Hat Enterprise Linux version.
          Reference: http://support.ts.fujitsu.com/com/support/downloads.html.




Page 16 of 19                                                                                                      www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01


PRIMERGY RX2540 M1 with CentOS 6.5 (x86_64)

Installation and Operational Checking Results with conf02
      PRIMERGY RX2540 M1 CentOS 6.5 (x86_64) 2.6.32-431.el6.x86_64
 No.        Item checked                                                                                        Result
 1         Is there HDD/RAID driver support? (OS standard or special)                                           OS Standard
 2         Is there LAN driver support? (OS standard or special)                                                Special(*1)
 3         Is installation possible in the verification machine?                                                OK(*2)
 4         Is reboot possible after installation, and does the OS start correctly?                              OK
 5         Can the GUI be used?                                                                                 OK
 6         Can the keyboard be used?                                                                            OK
 7         Can the mouse be used?                                                                               OK
 8         After OS start, is login as a root user possible?                                                    OK
 9         Can a USB stick disk be used?                                                                        -
 10        Can the CD/DVD-ROM drive be used?                                                                    OK
 11        When logged in as a root user, does the “shutdown -h now” command perform shutdown?                  OK
 12        Confirmation of write to local disk (write, delete, etc.)                                            OK
 13        Are the values set during installation displayed correctly (ifconfig command)?                       OK
 14        Can a ping be sent from the verification machine to another PC?                                      OK
 15        Can a ping be sent to the verification machine from another PC?                                      OK
 16        Can a network utility (system-config-network*, etc.) be used to change the network configuration?    OK
 17        Can the web service (httpd) be used?                                                                 OK
 18        Can the ftp service be used?                                                                         OK
 19        Can the nfs service be used?                                                                         OK
 20        Can the Network data transfer (nfs) be used?                                                         OK
 21        Result of disk array management tool [ServerViewRAID] installation?                                  OK
 22        Result of server management software [ ServerView agents ] installation?                             OK
 23        Does the OS run even if the HDD on one side is removed? * Remove HDD when stopped, and then start    -(*3)
 24        Is login as a root user possible if the HDD on one side is removed?                                  -(*3)
 25        Can the touch command be used to write if the HDD on one side is removed?                            -(*3)
 26        Does the OS start when restart is performed if the HDD on one side is removed?                       -(*3)
 27        Is the RAID configuration rebuilt when the RAID on one side is put back?                             -(*3)
 28        Is reboot possible and does the OS start correctly after RAID configuration rebuilding ends?         -(*3)
 29        Is login as a root user possible after RAID configuration rebuilding ends?                           -(*3)
 30        48 hours stress test of CPU, HDD and network using cpubench, bonnie and phoronix test suite          -(*3)
*1 The driver can be obtained from the following site.
  URL: http://support.ts.fujitsu.com/download/index.asp
      Select as follows
       Product selection(manually search) : Fujitsu Server PRIMERGY -> PRIMERGY RXxxx
       -> PRIMERGY RX2540 M1 -> Red Hat Enterprise Linux -> Red Hat Enterprise Linux 6(x86_64)
       -> LAN -> Emulex XE104/XE102 -> RHDUP driver package be2net 10.2.346.0-1 for RHEL6.5
     [Driver Information]
         Date : 17.07.2014
         Size : 0.21MB
         Version : 10.2.346.0-1-0
         Manufacturer : Fujitsu Technology Solutions

*2 Even if the USB ports is not used, disable the USB3.0 function.
    Select as follows
      BIOS menu : Advanced -> USB Configuration -> xHCI Mode -> Disabled
*3 Done with the corresponding Red Hat Enterprise Linux version.



Page 17 of 19                                                                                                  www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01



  ■ Installation procedure

     1.   After DVD boot, select [Install or upgrade an existing system] and press Enter.
     2.   Follow usual procedure for remainder of install.
     3.   The relevant Server Management Software (ServerView) including manuals are located on the Fujitsu download site of the respective
          server for the corresponding Red Hat Enterprise Linux version.
          Reference: http://support.ts.fujitsu.com/com/support/downloads.html.




Page 18 of 19                                                                                                      www.fujitsu.com/primergy
Test Report PRIMERGY RX2540 M1 with CentOS 2015-07-01




Contact                                                   ƒ Copyright 2010 [Fujitsu company name] Fujitsu, the Fujitsu logo, [other Fujitsu trademarks /registered
FUJITSU [Company Name]                                    trademarks] are trademarks or registered trademarks of Fujitsu Limited in Japan and other countries. Other
Address: x-xx-x, street, city, state, ZIP code, country   company, product and service names may be trademarks or registered trademarks of their respective owners.
Phone: xx-xxxx-xxxx                                       Technical data subject to modification and delivery subject to availability. Any liability that the data and
Fax : xx-xxxx-xxxx                                        illustrations are complete, actual or correct is excluded. Designations may be trademarks and/or copyrights of
E-mail: xxx.xxxxx@xx.fujitsu.com                          the respective manufacturer, the use of which by third parties for their own purposes may infringe the rights of
Website: www.fujitsu.com/[Country Code]                   such owner. [Other disclaimers]
YYYY-MM-DD [Region Code] [Language Code]

Page 19 of 19                                                                                                                                 www.fujitsu.com/primergy
You can also read
Next part ... Cancel