Speciality doors & tilt fittings - Flex-A-Door Design-A-Door Tilt-A-Dor Natural Timber Doors - B&D Garage Doors
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
speciality doors & tilt fittings Flex-A-Door ® Design-A-Door ® Tilt-A-Dor ® Track Fittings Jamb Fittings Natural Timber Doors Timberpanel™ Craftpanel™
Product Code
R1X
sliding overhead garage door
size range
Available in sizes to suit up to 2790mm door height
and 1200mm to 3150mm opening width.
features
• Flex-A-Door is much easier to use, as it is light to
lift, and does not require the out / up action of
traditional tilt doors.
• The springs are enclosed and above head height
- well out of the reach of children, and there are
no moving brackets or door supports which could
act as finger or arm entrapments.
• Flex-A-Door has an optional patented retractable
head infill panel for use in low headroom
situations.
description • Nylofelt ® running strips and nylon rollers with
The B&D Flex-A-Door ® offers an alternative to the bearings ensure smooth, quiet, greaseless
tilting door in situations with minimal headroom operation.
clearance. • Plastic insert in horizontal track provides smooth,
quiet operation.
Flex-A-Door doors revolutionary, patented design
comprises the durable, attractive Roll-A-Door ® • Steel track/brace and door stops, with buffers for
curtain, fitted on a curving track, to lift from a added safety and quietness.
vertical position up into a horizontal position, close • Weatherseal with deep cushioning, helps restrict
to the ceiling. entry of water and leaves.
• Waist height centre lift lock with double bar
profile locking action for extra security.
• Flex-A-Door utilises the Roll-A-Door curtain,
PANEL PROFILE providing a clean, neat appearance of the door
on both the outside and the inside.
• Centre lift lock has a deep finger recess
MODEL Flex-A-Door externally and turn knob internally for easier
operation.
MODEL CODE R1X
• Door can be left open at any height, unlike
COIL THICKNESS 0.4mm
the traditional tilt door, giving the added
coil type G300 COLORBOND ® convenience of allowing the door to be partially
MAX DOOR HEIGHT 2790mm opened for ventilation, while still providing
MAX DOOR WIDTH 3150mm privacy in the garage, and the door won’t blow
shut in the wind.
locking Centre lift lock
• Flex-A-Door fits behind the opening, restricting
TAPER OPTION No
the wind from blowing through the entry way, as
high wind option No happens with jamb tilt doors, which fit within the
opening and therefore have a gap on each side.
• Flex-A-Door is suitable for installation with
sectional automatic garage door openers
providing added convenience and security.
• Tailor made - each door is tailor made to order.
Available in 5mm width increments to
perfectly suit the application.
• Springs designed to comply with
requirements of Australian Standards
- 20,000 cycles. July 2018
RETURN TO INDEX SECTION 03/1Product Code
R1X
sliding overhead garage door
colours/finishes options
Available in • Perforations for ventilation.
• Extensive range of Colorbond colours plus ®
• Retractable head infill panel.
Zincalume ® finish (see colour chart for details).
installation requirements
INSTALLATION CLEARANCES
Headroom without Retractable Head Minimum
Retractable Head Infill Infill Panel Option Garage
Product Heights Panel Option A B Sideroom Depth
E
Manual Opener Manual Opener (manual
operation)
Up to 2130 180 210 90 120 100 2950
R1X
2131 to 2790 180 210 90 120 100 3610
All measurements are in millimetres and are minimum unless otherwise shown.
Retractable
➝ Head Infill
Panel
Headroom
Flex-A-Door ® curtain Flex-A-Door ® curtain
in closed position in open position
Notes / Information
A) For areas within one kilometre of a corrosive environment eg. salt air or industrial fallout, special care and maintenance are generally required for metal
products. Consult B&D Doors or your B&D Dealer for advice.
B) Flex-A-Door garage doors, in normal residential use are covered by a one year warranty for all components and labour conditional on care and servicing as
recommended in the door’s handbook. Full details of the warranty are available, on request, from your nearest B&D office.
C) The company reserves the right to make changes or improvements to the products or accessories without notice and without incurring any obligation to make
similar changes or improvements to goods previously ordered.
D) Prefixed Trademarks are trademarks of B&D Australia Pty. Ltd. Abuse of these trademarks may result in legal action.
E) B&D products have many patents and registered designs applicable.
F) Flex-A-Door has “PATENT APPLIED FOR, Provisional Patent Application No 2004901986”
G) Colorbond ® and Zincalume ® are registered trademarks of BlueScope Steel Limited.
H) While BlueScope Steel is our preferred supplier, steel products from other sources may also be used.
I) Details correct at date of publication. Specifications subject to change without notice.
July 2018
RETURN TO INDEX SECTION 03/2Product Code
P7D
residential sectional garage door
size range
Available in sizes from 1370mm to 3420mm height
and 1800mm to 6600mm in width (slat profile
5900mm max).
Inserts measure up to 525mm high, and up to
1428mm wide. The insert size cannot be changed.
Width is limited to 1200mm for some inserts, check
with your B&D representative for further details.
Your B&D Design-A-Door will suit your garage
opening with equal sized panels and evenly
spaced inserts.
features
• Frames available in natural aluminium finish or
choose from over 100 Dulux standard powder
description coat colours.
The B&D Design-A-Door ® features an aluminium
• Choose from a range of insert options or combine
powder coated door frame which has a high
different inserts to suit your requirements.
strength to weight ratio. Customer has the flexibility
to select from a range of different insert options, to • Galvanised hinges and hangers are used,
design a door that suits the look of their home. providing the door with:
- Additional strength.
The sectional garage door is made up of a number
- Durability.
of rigid sections that are hinged together and move
- Resistance to corrosion.
vertically in the opening, then horizontally along the
ceiling, guided by tracks and counterbalanced with • The aluminium frame is constructed from 1.5mm
springs. thick, box shaped extrusion with tongue and
groove top and bottom edges for weather
protection. For wide doors addition web
profile extrusions are included for additional strength.
PANEL PROFILE • Inserts fitted using snap-on extrusions and glazing
seals.
• Each door is tailor made to suit the size required.
• Wheels have ballbearings for smoother, more
durable operation.
• Springs designed to comply with requirements of
insert profile Varies for each insert Australian Standards - 20,000 cycles.
MODEL Design-A-Door
• Reinforcing for wide doors - all panels reinforced
MODEL CODE P7D for door widths of 3800mm and over.
extrusion THICKNESS 1.5mm
• Can be manually or electrically driven with
MAX DOOR HEIGHT 3420mm either domestic Controll-A-Door or industrial
MAX DOOR WIDTH 6600mm (slat profile commercial Axess opener.
5900mm max)
TAPER OPTION Hinged and fixed
option
high wind option No
July 2018
RETURN TO INDEX SECTION 03/3Product Code
P7D
residential sectional garage door
colours/finishes options
Frame available in aluminium finish or in over 100 • Tapers - for garage floors that slope across the
powder coating colour options from the standard opening.
Dulux ® range.
Inserts available in Design-A-Door ® assorted panel inserts
1. The sheer panel can be chosen from a broad
range of colours in aluminium composite
and acrylic materials which comply to group
1 classified materials tested to AS ISO 9705.
The design is available in a number of panel
configurations providing many options (refer to
the b&d brochure for all options).
1. Sheer panel 2. Alumpanel™
2. Alumpanel™ inserts - aluminium stucco available
in natural aluminium or powder coated in a
choice of over 100 colours.
3. Alumpanel™ with air inserts - in natural aluminium
or powder coated in a choice of over 100
colours. Perforation Material: 1 mm thick
aluminium grade 5005-H34. Perforations: 3.25mm
diameter @ 6.1mm staggered pitch. 3. Alumpanel™ with Air 4. Aluminium checker
plate
Open Area: 25.74%.size 3.18mm round holes.
4. Aluminium plate inserts - in natural aluminium
finish or powder coated in a choice of over 100
colours, in: a. Checker plate pattern
5. Acrylic panel inserts - 4.5mm acrylic inserts
available in clear, smoke or opaque finish.
6. Mini corrugated steel inserts - powder coated in
5. Acrylic 6. Mini corrugated steel
a choice of over 100 colours.
7. Vertipanel™ inserts - available in aluminium or
powder coated in a choice of over 100 colours.
8. Airpanel™ inserts - attractive Amplimesh 68A grill
design offering 80% airflow. Available in aluminium
or powder coated in a choice of over 100 colours.
9. Aluminium slatted - Powdercoated or
Knotwood™ Timber Look - 50mm x 10mm with a 7. Vertipanel™ 8. Airpanel™
large range of colours. Maximum width for slat
profile is 5900mm - up to approx. 40% airflow
can be achieved by adjusting the slat spacing.
Acrylic or Colorbond steel can be added to
slatted doors for additional weather protection
(door size restrictions apply).
10. Flat steel inserts in a choice of smooth or
wood look embossed. Available in a range of 9. Aluminium slatted 10. Flat steel
Colorbond colours including Timbagrain.
11. Ribbed steel inserts in a choice of smooth or
wood look embossed. Available in a range of
Colorbond colours including Timbagrain.
12. Omnipanel™ inserts - allows you to combine
different inserts to suit your design requirements.
This great versatility means the P7 door can be
used in an extensive range of applications. 11. Ribbed steel
July 2018
RETURN TO INDEX SECTION 03/4Product Code
P7D
residential sectional garage door
installation requirements
INSTALLATION CLEARANCES - standard headroom
Headroom (mm) Sideroom (mm)
Recommended
Recommended With Opener
each side
From (incl.) To (incl.) Up to 4710 to Over Up to 4710 to Over
Height Height 4705W 5285W 5285W 4705W 5285W 5285W
1825 2275 340 340 340 390 390 390 120
2280 2850 340 340 390 390 390 440 120
2855 3420 340 390 390 390 440 440 120
INSTALLATION CLEARANCES - low headroom
Headroom (mm) Sideroom (mm)
Recommended
Recommended With Opener
each side
From (incl.) To (incl.) Up to 4710 to Over Up to 4710 to Over Up to Over
Height Height 4705W 5285W 5285W 4705W 5285W 5285W 15m2 15m2
1825 2275 190 190 190 240 240 240 155 195
2280 2850 190 190 200 240 240 250 155 195
2855 3420 190 200 200 240 250 250 155 195
Note: Sideroom dimensions include door overlap, of Notes / Information
A) For areas within one kilometre of a corrosive environment eg. salt air or
opening, of 30mm on each side. All measurements industrial fallout, special care and maintenance are generally required
for metal products. Consult B&D Doors or your B&D Dealer for advice.
are in millimetres and are minimum unless otherwise
B) Design-A-Door garage doors, in normal residential use are covered by
shown. a one year warranty for all components and labour conditional on care
and servicing as recommended in the door’s handbook. Full details of
the warranty are available, on request, from your nearest B&D office.
C) The company reserves the right to make changes or improvements to
the products or accessories without notice and without incurring any
obligation to make similar changes or improvements to goods previously
ordered.
D) Prefixed Trademarks are trademarks of B&D Australia Pty. Ltd. Abuse of
these trademarks may result in legal action.
E) B&D products have many patents and registered designs applicable.
F) Details correct at date of publication. Specifications subject to change
without notice.
July 2018
RETURN TO INDEX SECTION 03/5track fittings
features
• Springs designed to comply with requirements of
Australian Standards - 20,000 cycles.
• New patented spring restraint feature to ensure
that spring movement is contained, and
eliminates the possibility of spring separation from
the fitting.
• Enclosed spring ends restrict spring movement
and consequently decrease the chance of
spring escape.
• Springs provide optimum performance
throughout the working life of the fittings.
• Minimal installation clearances required giving
the fittings the ability to fit where some other
styles of garage doors will not.
• Supplied with weatherstrip for fitting to the door
description panel, to help restrict entry of water and leaves.
The B&D range of Tilt-A-Dor ® fittings offer the
• Strengthened bearing design for greater
opportunity to create a door that is in harmony with
durability over the life cycle of the fittings.
its surroundings, giving the building a truly tailored
and unique appearance. • Robust anti-sway bracket to limit the degree of
lateral movement.
With durability and safety primary concerns, B&D
Tilt-A-Dor fittings offer the quality that is expected • Available in a number of configurations to suit
with all B&D Doors, and provide you with the both single and double width openings.
opportunity to design a door that is only limited by • Can be fitted with a Controll-A-Door ® Sectional
your imagination. Door Opener to ensure effortless operation.
Tilt-A-Dor fittings are available in Track
configurations. Track fittings fit alongside the door colours/finishes
and raise and support the door so that it rests on a
track that hangs horizontally just below the height The B&D tilt fitting range is available in a powder
of the ceiling. coat finish. This offers greater durability and
resistance to corrosion.
July 2018
RETURN TO INDEX SECTION 03/6track fittings
selection charts xyz distance on installation
Single Spring/Side This table is only for door thickness up to 50mm
(50mm door thickness used in this calculation).
2851 min
2850 max P/ARM MAIN
NEW REO-PLATE
2451 min PIVOT- PIVOT POS.
Door Height (mm)
MODEL POS. "X"
PIVOT "Y" "Z"
2450 max 70-T-2450 100-T-2450
2251 min Brown Spring Brown Spring 70-T-1950
1673 775 913
OT1804
2250 max 70-T-2250 100-T-2250
1951 min Brown Spring Brown Spring 70-T-2250
1843 870 988
OT1805
1950 max 70-T1950 100-T-1950
1800 min Brown Spring Brown Spring 70-T-2450
2138 1020 1133
OT1806
Door Weight
30 70 71 100
(kg) 100-T-1950
1673 775 913
OT1807
DOUBLE Spring/Side 100-T-2250
1843 870 988
OT1808
120-T-3050 175-T-3050
3050 max 100-T-2450
Orange Orange 2138 1020 1133
2701 min
Door Height (mm)
Spring Spring OT1809
120-T-2700 175-T-2700 120-T-2100
2700 max 1673 775 913
Orange Orange OT1812
2401 min
Spring Spring 120-T-2400
1843 870 988
2400 max 120-T-2400 175-T-2400 OT1813
2101 min Brown Spring Brown Spring 120-T-2700
2138 1020 1133
2100 max 120-T-2100 175-T-2100 OT1814
1900 min Brown Spring Brown Spring 120-T-3050
2448 1170 1293
Door Weight OT1815
101 120 121 175
(kg) 175-T-2100
1673 775 913
OT1816
SPRING SPECIFICATIONS 175-T-2400
1843 870 988
Wire Spring Active OT1817
Colour
Dia. OD Length 175-T-2700
2138 1020 1133
Brown 5.6 41 542 OT1818
Orange 5.6 41 695 175-T-3050
2463 1170 1308
OT1819
LINTEL
For door with thickness more than 50mm.
For example:
Z Reo Plate Dimensions
300 x 180 x 2.0 mm
120 x 180 x 1.0 mm
X
Door thickness 70mm
X = 1673 + (70 - 50mm) = 1693mm
MODEL: 70-T-1950
Z
USE M4 (6 off)
TEK Screw
Steel REO-Plate (300x180x2)
2 off supplied
Cut any excessive material here
FLOOR
July 2018
RETURN TO INDEX SECTION 03/7TILT TRACK
TRACK TYPE LENGTH
70-100-T-1950 1710
70-100-T-2250 1890
TOP WEATHER STRIP
MODEL "LENGTH" "WIDTH"
70-100-T-2450 1935 TYPICAL TILT DOOR 70-100-T-1950 600 47
120-T-2100 1710
70-100-T-2250 675 47
120-T-2400 1890 TRACK BRACKET
70-100-T-2450 700 47
120-T-2700 2190
120-T-2100 600 65
RETURN TO INDEX
120-T-3050 2515
120-T-2400 675 65
175-T-2100 1765
120-T-2700 700 65
175-T-2400 1935
track fittings
120-T-3050 800 65
175-T-2700 2230
175-T-2100 600 80
175-T-3050 2555
175-T-2400 675 80
175-T-2700 700 80
PERFORATED ANGLE 175-T-3050 800 80
KICKER
ASSEMBLY MAIN X KICKER ASSEMBLY
PIVOT
SHAFT
DOUBLE SPRING
MAIN HOOK
PIVOT
BRACKET
B
A Y
POWER ARM
X-SECTION
DOUBLE SPRING INSTALLATION
SHOWN RIGHT SIDE ONLY
120-175-T-2100-2400 4 x Brown Springs
120-175-T-2700-3050 4 x Orange Springs
FOOT BRACKET
POWER ARM REO PLATE POS. SINGLE SPRING INSTALLATION BOTTOM WEATHER STRIP
TO TOP OF DOOR SHOWN LEFT SIDE ONLY MODEL LENGTH
70-100-T (All Models) 2 x Brown Springs 70-100-T-1950 1480 PIG TAIL
MODEL "Y" "A" "B" "X"
70-T-1950 775 41 3 1673 70-100-T-2250 1705
70-T-2250 870 41 3 1843 120-175-T-2100 1480
70-T-2450 1020 41 3 2138 120-175-T-2400 1705 SPRING ANCHOR
100-T-1950, 120-T-2100 775 47 4 1673 120-175-T-2700 1980 BRACKET
100-T-2150, 120-T-2400 870 47 4 1843 120-175-T-3050 2555
100-T-2450, 120-T-2700 1020 47 4 2138
120-T-3050 1170 47 4 2448
175-T-2100 775 52 4 1673
175-T-2400 870 52 4 1843
175-T-2700 1020 52 4 2138 REINFORCING
175-T-3050 1170 52 4 2463 PLATE
July 2018
SECTION 03/8
AWING LOCATION= M:\Bianto S\Projects\TAD Rationalisation\TRACK\CAD\TAD\DESIGN DEVELOPMENT
NOTE: INTERIM SPRINGS SPECS
SINGLE SPRING INTERIM
50-T (All Models) 2 x Blue Springs
70-T (All Models) 2 x Yellow Springs
120-T (All Models) 4 x Yellow Springstrack fittings
size range
The extensive range of B&D tilt fittings suit one piece doors weighing between 30 and 175kg and heights of
1800mm to 3050mm.
Height (mm)
Weight 1800 1851 1901 1951 2101 2251 2401 2451 2701
(kgs) to to to to to to to to to
1850 1900 1950 2100 2250 2400 2450 2700 3050
30 to 70 70-T-1950 70-T-2250 70-T-2450
71 to 100 100-T-1950 100-T-2250 100-T-2450
101 to
120-T-2100 120-T-2400 120-T-2700 120-T-3050
120
121 to 175 175-T-2100 175-T-2400 175-T-2700 175-T-3050
installation requirements
Installation Clearances
Headroom
Fitting Type Sideroom
Manual Opener
70mm (Model 70-T, 100-T, 120-T)
Track 50mm 100mm
90mm (Model 175-T)
Door Panel Clearances
Manufactured Door
Fitting Type Manufactured Door Width X
Height
Track Opening Height - 27mm Opening Width - 20mm 15mm
* This is accurate for standard installations. All doors require diagonal measurements. All measurements are in millimeters and are minimum
unless otherwise shown.
Notes / Information
Headroom x A) For areas within one kilometre of a corrosive environment eg. salt air or
industrial fallout, special care and maintenance are generally required
for metal products. Consult B&D Doors or your B&D Dealer for advice.
B) Tilt-A-Dor fittings, in normal residential use, are covered by a two year
Opening Height
warranty for all components and labour conditional on care and
Door Height
servicing as recommended in the door’s handbook. Full details of the
Sideroom
warranty are available, on request, from your nearest B&D office.
C) The company reserves the right to make changes or improvements to
the products or accessories without notice and without incurring any
obligation to make similar changes or improvements to goods previously
ordered.
D) Prefixed Trademarks are trademarks of B&D Australia Pty. Ltd. Abuse of
these trademarks may result in legal action.
Door Width 12mm E) B&D products have many patents and registered designs applicable.
10mm 10mm
Opening Width F) Details correct at date of publication. Specifications subject to change
without notice.
NOTE: Measurement X will vary depending on door thickness.
July 2018
RETURN TO INDEX SECTION 03/9jamb fittings
features
• Springs designed to comply with requirements of
Australian Standards - 20,000 cycles.
• New patented spring restraint feature to ensure
that spring movement is contained, and
eliminates the possibility of spring separation from
the fitting.
• Enclosed spring ends restrict spring movement
and consequently decrease the chance of
spring escape.
• Springs provide optimum performance
throughout the working life of the fittings.
• Minimal installation clearances required giving
the fittings the ability to fit where some other
styles of garage doors will not.
• Strengthened bearing design for greater
durability over the life cycle of the fittings.
• Available in a number of configurations to suit
both single and double width openings.
description • Can be fitted with a Controll-A-Door ® Sectional
Door Opener to ensure effortless operation.
The B&D range of Tilt-A-Dor ® fittings offer the
opportunity to create a door that is in harmony with
its surroundings, giving the building a truly tailored colours/finishes
and unique appearance. The B&D tilt fitting range is available in a powder
With durability and safety primary concerns, B&D coat finish. This offers greater durability and
Tilt-A-Dor fittings offer the quality that is expected resistance to corrosion.
with all B&D Doors, and provide you with the
opportunity to design a door that is only limited by
your imagination.
Tilt-A-Dor fittings are available in Jamb
configurations. Jamb fittings fit alongside the door
and raise and support the door so that it rests
horizontally just below the height of the ceiling.
This fitting is ideal where there is limited internal
backroom as the panel does not fully retract.
July 2018
RETURN TO INDEX SECTION 03/10jamb fittings
selection charts
Spring SPRING SPECIFICATIONS
70J & 70J Wire Spring Active
Colour
Door Height
2250 max 90J Dia. OD Length
S/Fix
1800 min Black Spring
(mm)
Green Spring Green 5 38 695
Door Weight Black 6 43.6 740
30 70 71 90
(kg)
installation requirements
Installation Clearances
Headroom
Fitting Type Sideroom
Manual Opener
70mm (Model 50-T, 120-T)
Jamb 25mm - 125mm 100mm - 175mm
50mm
NOTE: Openers are only recommended to be fitted in position 1 or 2.
Door Panel Clearances
Manufactured
Fitting Type Manufactured Door Width X
Door Height
Jamb Opening Height - 27mm Opening Width - 20mm 15mm
* This is accurate for standard installations. All doors require diagonal measurements. All measurements are in millimeters and are minimum
unless otherwise shown.
Notes / Information
Headroom x A) For areas within one kilometre of a corrosive environment eg. salt air or
industrial fallout, special care and maintenance are generally required
for metal products. Consult B&D Doors or your B&D Dealer for advice.
B) Tilt-A-Dor fittings, in normal residential use, are covered by a two year
Opening Height
warranty for all components and labour conditional on care and
Door Height
servicing as recommended in the door’s handbook. Full details of the
Sideroom
warranty are available, on request, from your nearest B&D office.
C) The company reserves the right to make changes or improvements to
the products or accessories without notice and without incurring any
obligation to make similar changes or improvements to goods previously
ordered.
D) Prefixed Trademarks are trademarks of B&D Australia Pty. Ltd. Abuse of
these trademarks may result in legal action.
Door Width 12mm E) B&D products have many patents and registered designs applicable.
10mm 10mm
Opening Width F) Details correct at date of publication. Specifications subject to change
without notice.
NOTE: Measurement X will vary depending on door thickness.
July 2018
RETURN TO INDEX SECTION 03/11KICKER ASSEMBLY
DISTANCE DOOR TRAVELS
TYPICAL TILT DOOR 0 200 400 600 800 1000 mm
HEIGHT: 1800 - 2250 mm 125
WEIGHT: 30 - 90 kg 1
LINTEL 100
75
RETURN TO INDEX
2 50
DETAIL A 25
SCALE 1:5 0
jamb fittings
-25
3 -50
DOOR HEADROOM
-75
-100
70J SIDE FIX ASSEMBLY D* -125
SEE DETAIL C
DETAIL C
SCALE 1:5
SEE DETAIL A
HOLE No.1
HOLE No.2
HOLE No.3
HOLE No. 1 2 3
MEASURE DOWN 510 480 435
D* = MEASURE DOWN + DOOR THICKNESS
70J SIDE FIX SPRING
ANCHOR BRACKET
SEE DETAIL B
PIG TAIL
SINGLE SPRING INSTALLATION
70J & 70J S/F 2 x Green Springs Door Weight 30 - 70 kg
SPRING ANCHOR 90J 2 x Black Springs Door Weigth 70 - 90 kg
BRACKET
DETAIL B
SCALE 1:5
DRAWING LOCATION: M:\Bianto S\Projects\TAD Rationalisation\JAMB\CAD\Bearing with bushing
July 2018
SECTION 03/12Timberpanel Product Code
P4W
residential sectional garage door
size range
Available in sizes from 1870mm to 2660mm in height
and from 2020mm to 5500mm in width.
features
• Tongue & groove edge panel profile.
• Galvanised hinges.
• Tailor made - each door is tailor made to order.
(They are not made up from a mix of standard
size panels).
• Wheels have ballbearings for smoother, more
durable operation.
• Springs designed to comply with requirements of
Australian Standards - 20,000 cycles.
description
The Timberpanel™ door is a timber sectional
overhead garage door with timber boards across
each panel.
The Timberpanel door features slim horizontal
boards made from the highest quality Western Red
Cedar and strengthened with aluminium extrusion
for extra support.
The sectional garage door is made up of a number
of rigid sections that are hinged together and move
vertically in the opening, then horizontally along the
ceiling, guided by tracks and counterbalanced with
springs.
profile
PANEL PROFILE
PATTERN OR RIB TYPE
MODEL Timberpanel
MODEL CODE P4W
door surface Western Red Cedar
MAX DOOR HEIGHT 2660mm
MAX DOOR WIDTH 5500mm
TAPER OPTION Yes
high wind OPTION No
July 2018
RETURN TO INDEX SECTION 03/13Timberpanel Product Code
P4W
residential sectional garage door
colours/finishes options
B&D Timberpanel doors have two thick coats of • Tapers - for garage floors that slope across the
Sikkens THB 077, natural colour, over the Sikkens HLS opening.
base sealer coat for weather protection.
• External lock.
installation requirements
INSTALLATION CLEARANCES
Headroom (mm) Sideroom (mm)
Recommended Restricted With Opener Recommended each side
Height Width
Standard Low Standard Low Standard Low
Headroom Headroom Headroom Headroom Headroom Headroom
Up to Over Up to Over Up to Over
5285W 5285W 5285W 5285W 13m2 13m2
To 2850 To 5500 375 375 190 200 425 240/250 110 155 195
Recommended backroom Notes / Information
A) For areas within one kilometre of a corrosive environment eg. salt air or
clearance requirements industrial fallout, special care and maintenance are generally required
for metal products. Consult B&D Doors or your B&D Dealer for advice.
Rear Torsion - 680mm plus door height.
B) Timberpanel doors, in residential use, are covered by a 12 month
Standard Headroom - 540mm plus door height. warranty on the structual integrity of the door (excludes salt corrosion),
conditional on proper care, as recommended in the door’s handbook.
Standard Headroom with Opener - 1000mm plus Due to timber being a natural product, we are not able to warrant the
door height. timber for the final quality of the look or finish. Full details of the warranty
are available from www.bnd.com.au. Warranty only applies to doors
purchased and installed in Australia or New Zealand. Warranty only valid
Note: Sideroom dimensions include door overlap, of if warranty conditions are met.
opening, of 30mm on each side. All measurements C) The company reserves the right to make changes or improvements to
the products or accessories without notice and without incurring any
are in millimetres and are minimum unless otherwise obligation to make similar changes or improvements to goods previously
ordered.
shown.
D) Prefixed Trademarks are trademarks of B&D Australia Pty. Ltd. Abuse of
these trademarks may result in legal action.
E) B&D products have many patents and registered designs applicable.
F) Details correct at date of publication. Specifications subject to change
without notice.
July 2018
RETURN TO INDEX SECTION 03/14Craftpanel Product Code
P4T
residential sectional garage door
size range
Available in sizes from 1870mm to 2830mm in height
and from 2020mm to 5500mm in width.
features
• Tongue & groove edge panel profile.
• Galvanised hinges.
• Custom pattern positioning - raised patterns are
evenly spaced over area of door.
• Tailor made - each door is tailor made to order.
(They are not made up from a mix of standard
size panels).
• Wheels have ballbearings for smoother, more
durable operation.
description
• Springs designed to comply with requirements of
Timber sectional overhead garage door with Australian Standards - 20,000 cycles.
raised patterns across each panel.
The door is made from solid Western Red Cedar and
is constructed in the traditional joinery fashion - with
stiles, rails and raised pattern inserts.
The sectional garage door is made up of a number
of rigid sections that are hinged together and move
vertically in the opening, then horizontally along the
ceiling, guided by tracks and counterbalanced with
springs.
profile
PANEL PROFILE
PATTERN OR RIB TYPE
MODEL Craftpanel
MODEL CODE P4T
door surface Western Red Cedar
MAX DOOR HEIGHT 2830mm
MAX DOOR WIDTH 5500mm
TAPER OPTION Yes
high wind OPTION No
July 2018
RETURN TO INDEX SECTION 03/15Craftpanel Product Code
P4T
residential sectional garage door
colours/finishes options
B&D Craftpanel doors have two thick coats of • Tapers - for garage floors that slope across the
Sikkens THB 077, natural colour, over the Sikkens HLS opening.
base sealer coat for weather protection.
• External lock.
installation requirements
INSTALLATION CLEARANCES
Headroom (mm) Sideroom (mm)
Recommended Restricted With Opener Recommended each side
Height Width
Standard Low Standard Low Standard Low
Headroom Headroom Headroom Headroom Headroom Headroom
Up to Over Up to Over Up to Over
5285W 5285W 5285W 5285W 13m2 13m2
To 2850 To 5500 375 375 190 200 425 240/250 110 155 195
Recommended backroom Notes / Information
A) For areas within one kilometre of a corrosive environment eg. salt air or
clearance requirements industrial fallout, special care and maintenance are generally required
for metal products. Consult B&D Doors or your B&D Dealer for advice.
Rear Torsion - 680mm plus door height.
B) Craftpanel doors, in residential use, are covered by a 12 month
Standard Headroom - 540mm plus door height. warranty on the structual integrity of the door (excludes salt corrosion),
conditional on proper care, as recommended in the door’s handbook.
Standard Headroom with Opener - 1000mm plus Due to timber being a natural product, we are not able to warrant
door height. the timber for the final quality of the look or finish. Full details of the
warranty are available from www.bnd.com.au. Warranty only applies
to doors purchased and installed in Australia or New Zealand. Warranty
Note: Sideroom dimensions include door overlap, of only valid if warranty conditions are met.
opening, of 30mm on each side. All measurements C) The company reserves the right to make changes or improvements to
the products or accessories without notice and without incurring any
are in millimetres and are minimum unless otherwise obligation to make similar changes or improvements to goods previously
ordered.
shown.
D) Prefixed Trademarks are trademarks of B&D Australia Pty. Ltd. Abuse of
these trademarks may result in legal action.
E) B&D products have many patents and registered designs applicable.
F) Details correct at date of publication. Specifications subject to change
without notice.
July 2018
RETURN TO INDEX SECTION 03/16You can also read
