Getting the best from your new cleaner...
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
8537 Upright Currys cyclone ib 12/05/2003 18:12 Page 1
Ultralight cyclone vacuum cleaner
Please read and keep these
instructions
73313
getting the best from
your new cleaner...
If your cleaner isn’t picking up as
well as it should, please check
• Dust canister
It is important to empty the canister when full, otherwise the
performance of the cleaner will be impaired.
• Filters
It is important that the filters are cleaned regularly to allow air
through the appliance. Wash the cannister filters regularly in
warm water and allow to air dry.
• Blockages
Check the hose, tubes and tools for blockages
• Belt
Check and replace damaged or broken belt
www.morphyrichards.co.uk8537 Upright Currys cyclone ib 12/05/2003 18:12 Page 2
Important safety • Never use the appliance to vacuum hot
ashes, broken glass, sharp objects or
instructions •
liquids.
Never modify the cleaner in any way.
• Always disconnect the appliance from the
The use of any electrical appliance mains supply after use or prior to
requires the following of common sense cleaning or emptying.
safety rules. • The appliance should never be left
Primarily there is danger of personal running unsupervised.
injury and secondly danger of damage to the • Repairs to electrical appliances are only
appliance and property. These are indicated to be undertaken by trained personnel.
in the instructions text by the following two Unprofessional repairs can be dangerous
conventions: for users.
WARNING: Danger of personal injury • Use only genuine Morphy Richards spare
IMPORTANT: Damage to the appliance parts and accessories
In addition we offer the following • Never over-extend the hose such that the
essential safety advice. cleaner is pulled over. If the cleaner is
knocked over, switch off before
Location attempting to upright.
• Never pick the cleaner up by the floor
• Do not use or keep this product outside nozzle when connected to the mains, use
when it is raining. the carrying handle.
• Do not store the appliance near hot • WARNING: Keep loose clothing, hair,
ovens or heating appliances. fingers etc. away from the floor
nozzle whenever the cleaner is
Mains lead connected to the mains.
• Disconnect from the mains supply before
• Do not allow the mains lead to become attempting to clear blockages, clear the
strained or run this appliance over it. brush or replace the belt.
• If the electrical cable becomes damaged
the complete cable assembly must be
replaced. Do not attempt this task Electrical
yourself, contact Morphy Richards using
the helpline number. requirements
Children
Check that the voltage on the rating plate
• Children do not understand the dangers of your appliance corresponds with your
associated with operating electrical house electricity supply which must be A.C.
appliances. Never allow children to use (Alternating Current).
this appliance. If the socket outlets in your home are not
suitable for the plug supplied with this
Other safety considerations appliance, the plug should be removed and
the appropriate one fitted.
• Never use in the presence of explosive WARNING: The plug removed from
liquids or vapours. the mains lead, if severed, must be
• Never pick up inflammable or poisonous destroyed as a plug with bared flexible
liquids such as petrol, copier toner, or cord is hazardous if engaged into a live
other volatile substances. Never pick up socket outlet.
acids, asbestos or asbestos dust. Should the fuse in the 13 amp plug
• Never use the appliance without the require replacement, a BS1362 13 amp fuse
filters installed. must be fitted.
28537 Upright Currys cyclone ib 12/05/2003 18:13 Page 3
A
Ú
Î
Ï Û
‡ Ì
Ó
Ô Ù
·
‚
⁄ Ò
¤ „
‹
‰
Â
Ê
Á
Ë
› È
fi Í
fl
Accessories included Cleaning brush Extension tubes
(stored in canister)
Furniture brush
Crevice tool
Features
È Handle release button
⁄ Vari power slider (only on certain models) Í Hose connector
¤ Front cover release Î Dust canister release
‹ Removable front cover Ï Dust canister lid
› Hepa exhaust filter Ì Pleated circular filter
fi Carpet height adjustment knob Ó Foam filter
fl Floor nozzle with powered brush Ô Dust canister
‡ Upper handle Central canister filter
· Flexible hose Ò Dust release button
‚ Cord storage with quick release cleat Ú Safety filter inter-lock
„ On/Off switch Û Cleaning brush (clipped inside canister)
‰ Carrying handle Ù Canister handle
 Nested extension tubes (2) ı Motor protection filter (shown page 6)
Ê Crevice nozzle ˆ Exhaust filter (page 6)
Á Furniture brush ˜ Belt cover (shown page 7)
Ë Main body ¯ Brush bar (page 7)
38537 Upright Currys cyclone ib 12/05/2003 18:13 Page 4
Assembly B Variable power D
certain models only
Warning: Do not plug in the cleaner
until it is assembled. Slide the variable power control to the
1 Carefully unpack all components. right to increase the suction power or to the
2 Lift cleaner body to upright position. left to decrease suction. This feature is most
3 Remove the two screws that are already useful when using the hose and accessories.
attached to the body. Use the minimum setting when vacuuming
4 From the rear of the cleaner, align the delicate fabrics/curtains etc. When not using
handle with groove and slide into the the hose it is advisable to keep the variable
body. If necessary, use thumb and finger slider set to maximum.
pressure to slide handle into position.
5 Fasten the handle with the two screws.
Using on carpets
Floor nozzle height 1 Place cleaner in its upright position.
adjustment C 2 Set the carpet height adjustment knob to
the desired position.
3 Release the mains cable by revolving the
Before using the cleaner the floor nozzle quick release cleat through 180º and
height must be set to the correct height. extend the cable fully.
Choose the setting which most closely 4 Plug the cable into the mains socket.
matches your floor surface, ie deep carpet 5 Step on the handle release button to
pile, medium carpet pile, short carpet pile or release the handle to the desired position
hard floor. E.
When using the attachments the cleaner 6 Press the on/off button to the ‘on’
must only be used in the upright position position.
with the carpet height adjustment knob set IMPORTANT: To prevent damage to
to deep carpet. carpets, never leave the cleaner switched on
in one place for an extended period.
• Never have the brushes set too low such
that the cleaner is hard to push.
B Certain models only D
min max
Use attachments E
C
Normal use
Floors
DEEP CARPET HARD FLOOR
Clean under furniture
Flat position
48537 Upright Currys cyclone ib 12/05/2003 18:13 Page 5
Using attachments Cleaning the filters
Follow previous steps 1-4 but set the To maintain suction, the filters must be
carpet height adjustment knob to the deep regularly taken out and cleaned. Failure to
carpet setting. clean the filters will reduce the suction and
5 Remove the hose connector from the rear will damage the motor if used for prolonged
of the cleaner and push the required periods. This may invalidate the guarantee. If
attachment firmly onto the end of the the filters become damaged they must be
hose. replaced.
• If additional length is required, attach one IMPORTANT: Do not operate the cleaner
or both extension tubes between the without the filters in place.
hose and tool.
6 Switch on/off. Circular pleated & foam filters G
IMPORTANT: Never over extend the hose
such that the cleaner is pulled over. IMPORTANT: The filters should be
cleaned regularly to maintain the
performance of the cleaner.
Emptying the dust 1 Remove the front cover and the canister.
2 Twist the canister lid Ï anti-clockwise
canister F and lift off.
3 Lift up the pleated circular filter Ì and
foam filter Ó beneath. The filters can be
When the dust canister is full it should be cleaned using the brush Û clipped inside
emptied immediately.
1 Remove the front cover ‹ by lifting the G
cover release lever ¤.
2 Lift-up the dust canister release Î and
pull the canister away from the main
body. Ì
3 Hold the canister by the handle Ù over a
dustbin and with your other hand press Ó
Û Ï
the dust release button Ò. The bottom of
the canister will drop down to release the
dirt. To close press the flap firmly until it
clicks into place.
4 Replace the canister by inserting the
base then pushing in the top. Replace the
front panel by aligning the bottom tabs
with the slots in the body, then pressing
in the top.
F
Î
¤
‹ Ù
Ò
58537 Upright Currys cyclone ib 12/05/2003 18:13 Page 6
the canister lid. The filters can be washed only but must be totally dry before re-fitting.
in warm water then left to air-dry The canister has a safety inter-lock that
naturally. IMPORTANT: Ensure the filters prevents it from being fitted back into place
are totally dry before re-fitting. Do not use if the filters have not been fitted correctly.
detergents.
Motor protection filter J
Central filter H
The motor protection filter is located
4 Lift the central canister filter out of the underneath the dust canister
canister. 1 Remove the dust canister.
5 Remove any attached dirt by using the 2 Lift out the filter and shake rigorously
brush. over a dustbin.
6 Re-assemble by replacing the central The filter may also be washed in water
canister filter into the canister. (no detergents) but must be totally dry before
7 Replace the foam filter then the pleated re-fitting.
circular filter into the top of the canister. 3 Replace the filter
Replacing the canister lid I Hepa exhaust filter J
8 Replace the canister lid by lining up the The non-washable Hepa exhaust filter is
arrows on the canister base and lid and located below the dust canister
twisting clockwise to lock into place I. compartment.
The canister may be washed in water 1 Remove the front cover.
2 Remove the Hepa filter by pulling forward
H at the top and lift it away.
3 Shake vigorously over a dustbin and use
the filter cleaning brush to clean dust out
of the pleats. Do not wash. The Hepa
filter should be replaced every six months
or sooner if it becomes damaged.
4 Replace the filter and the front cover.
Changing the belt
If the power brush stops rotating it is
likely that the drive belt has snapped (usually
because the brush has been stalled). A spare
belt is supplied. Replacement belts can also
be obtained from Morphy Richards or a
Service Agent.
I J
ı
ˆ
68537 Upright Currys cyclone ib 12/05/2003 18:13 Page 7
Removing the floor nozzle carpet height adjustment knob back on.
cover KL 13 Replace the two screws on the top of the
floor nozzle cover and the three screws
1 Disconnect the cleaner from the mains underneath the floor nozzle - do not
supply. overtighten.
2 Place the cleaner upside down in the flat
position.
3 Use a cross-head screwdriver to remove Safety cut-out
the two screws at the front and the
central screw under the height
adjustment mechanism K. If the cleaner overheats a motor
4 Turn the cleaner over and remove the protection thermostat will automatically
carpet height adjustment knob fi. switch the motor off. If this happens, switch
5 Remove the two screws at the rear and the cleaner off, unplug from the power
lift the rear of the cover over the handle supply and leave the cleaner to cool for at
release button and unclip the cover from least 30 minutes. Check the airways for
the front of the floor nozzle L. blockages and clean the filters before
restarting.
Replacing the belt MN
6 If the belt has broken, ensure all pieces
are removed.
Helpline
7 Lift off the belt cover ˜.
8 Grasp the brush bar ¯ at both ends and If you have any difficulty with your
lift straight up. appliance, do not hesitate to call us. We’re
9 Place one end of the new belt over the more likely able to help than the store from
metal motor shaft pin and the other where you bought the product.
around the pulley end of the brush N. Please have the following information
10 Align brush end plates with their guide ready to enable our staff to deal with your
slots and push the brush bar down into query quickly:
place. • Name of the product
11 Re-fit the belt cover. • Model number as shown on the
12 Re-fit the floor nozzle cover. Push the underside of the appliance.
K ˜ M
¯
L N
fi
78537 Upright Currys cyclone ib 12/05/2003 18:13 Page 8
Your two-year to indicate the date of initial purchase.
To qualify for the two-year guarantee the
guarantee appliance must have been used according to
the manufacturers instructions. For example
the filters shall have been regularly cleaned
• It is important to retain the retailers as instructed.
receipt as proof of purchase. Staple Morphy Richards shall not be liable to
your receipt to this back cover for future replace or repair the goods under the terms of
reference. the Guarantee where:
Please quote the following information if 1 The fault has been caused or is attributable
the product develops a fault. These numbers to accidental use, mis-use, negligent use or
can be found on the base of the product. used contrary to the manufacturers
recommendations or where the fault has
Model no. Serial no. been caused by power surges or damage
caused in transit.
All Morphy Richards Products are 2 The appliance has been used on a voltage
individually tested before leaving the factory. supply other than that stamped on the
In the unlikely event of any appliance proving products.
to be faulty within 28 days of purchase it 3 Repairs have been attempted by persons
should be returned to the place of purchase other than our service staff (or authorised
for it to be replaced. dealer).
If the fault develops after 28 days and 4 Where the appliance has been used for hire
within 24 months of original purchase, you purposes or non-domestic use.
should contact the helpline number quoting 5 Morphy Richards are not liable to carry out
model number and serial number on the any type of servicing work, under the
product, or write to Morphy Richards at the guarantee.
address shown. You will be asked to return 6 Consumables such as the filters and belt
the product (in secure, adequate packaging) are not covered by the guarantee.
along with a copy of proof of purchase. This guarantee does not confer any rights
Subject to the exclusions set out below (1-6), other than those expressly set out above
the faulty appliance will then be repaired or and does not cover any claims for
replaced and dispatched usually within consequential loss or damage. This
seven working days of receipt. guarantee is offered as an additional benefit
If for any reason this item is replaced and does not affect your statutory rights as a
during the 2-year guarantee period, the consumer.
guarantee on the new item will be calculated • This guarantee is valid in the UK and
from original purchase date. Therefore it is Ireland only.
vital to retain your original receipt or invoice
Morphy Richards products are
intended for household use only
Morphy Richards has a policy of
The After Sales Division,
continuous improvement in product
Morphy Richards Ltd, Mexborough,
quality and design. The Company, South Yorkshire, England, S64 8AJ
therefore, reserves the right to change
the specification of its models at any Helpline (office hours)
time. UK (local rate) 0870 060 2603
Republic of Ireland 1800 409119
VC73313M Rev 2 05/03You can also read
