UNITED STATES ENVIRONMENTAL PROTECTION AGENCY WASHINGTON, DC 20460
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
UNITED STATES ENVIRONMENTAL PROTECTION AGENCY
WASHINGTON, DC 20460
OFFICE OF CHEMICAL SAFETY
AND POLLUTION PREVENTION
August 3, 2021
Kellie MacLeod
P.F. Harris Manufacturing Company, LLC
P.O. Box 1922
Cartersville, GA 30120
Subject: Label Amendment – Registration Review Interim Decision Label Mitigation
and Alternate Brand Name (ABN) Notification per PRN 98-10
Product Name: Harris Termite Powder
EPA Registration Number: 3-14
Received Dates: 9/13/18 and 1/10/19
Decision Numbers: 545626 and 577398
Dear Kellie MacLeod:
The amended label referred to above, submitted in connection with registration under the
Federal Insecticide, Fungicide and Rodenticide Act (FIFRA), as amended, is acceptable.
This approval does not affect any conditions that were previously imposed on this
registration. You continue to be subject to existing conditions on your registration and any
deadlines connected with them.
The Agency, in accordance with the Federal Insecticide, Fungicide and Rodenticide Act
(FIFRA), as amended, has completed reviewing all of the information submitted with
your application to support the Registration Review of the above referenced product in
connection with the Disodium Octaborate Tetrahydrate Interim Decision, and has
concluded that your submission is acceptable.
In addition, the Agency is in receipt of your Application for Pesticide Notification under
Pesticide Registration Notice (PRN) 98-10 for the above referenced product. The Antimicrobials
Division (AD) has conducted a review of this request for its applicability under PRN 98-10 and
finds that the action requested falls within the scope of PRN 98-10. The alternate brand name
Mil-X Mold Stop has been added to the product record.
A stamped copy of your labeling is enclosed for your records. This labeling supersedes all
previously accepted labeling. Pursuant to 40 CFR 156.10(a)(6) you must submit one copy
of the final printed labeling before you release the product for shipment with the new
labeling. In accordance with 40 CFR 152.130(c), you may distribute or sell this product
under the previously approved labeling for 12 months from the date of this letter. After 12
months, you may only distribute or sell this product if it bears this new revised labeling or
subsequently approved labeling. "To distribute or sell" is defined under FIFRA section
2(gg) and its implementing regulation at 40 CFR 152.3.
FQPA Label Acceptable v.20200903Page 2 of 2
EPA Reg. No. 3-14
Decision Nos. 545626 and 577398
Should you wish to add/retain a reference to the company's website on your label, then
please be aware that the website becomes labeling under FIFRA and is subject to review by
the Agency. See FIFRA section 2(p)(2). If the website is false or misleading, the product
would be misbranded and unlawful to sell or distribute under FIFRA section 12(a)(1)(E).
40 CFR 156.10(a)(5) list examples of statements EPA may consider false or misleading. In
addition, regardless of whether a website is referenced on your product's label, claims made
on the website may not substantially differ from those claims approved through the
registration process, FIFRA section 12(a)(1)(B). Therefore, should the Agency find or if it
is brought to our attention that a website contains false or misleading statements or claims
substantially differing from the EPA approved registration, the website will be referred to
the EPA's Office of Enforcement and Compliance.
Your release for shipment of the product constitutes acceptance of these conditions. If
these conditions are not complied with, the registration will be subject to cancellation in
accordance with FIFRA section 6. If you have any questions, please contact me by
phone at 703-308-0034, or via email at garvie.heather@epa.gov.
Sincerely,
Heather A. Garvie
Senior Regulatory Advisor
Regulatory Management Branch 2
Antimicrobials Division
Office of Pesticide Programs
Enclosure: Stamped Accepted Label1
Disodium Octaborate Tetrahydrate GROUP: 8D INSECTICIDE/FUNGICIDE
08/03/2021
TERMITE POWDER
[ABN: Mil-X Mold Stop]
3-14
For Infestation & Prevention
Kills [Wood Destroying Insects] [,] [Mold & Fungi that Cause Wood Rot]
Odorless
Non-Flammable
Effective against: Termites, Beetles (Wood Destroying), Carpenter Ants,
Wood Rot and Mold
Makes 1 Gal. - Covers 200 sq. ft.
Effective for all interior and exterior lumber, plywood, logs, and wood-form composite
structural components.
For the prevention and remedial control of wood infesting organisms including: Carpenter Ants,
Decay Fungi, Mold, Termites and Wood Destroying Beetles
The solution continues to penetrate deep into wood and does not break down, giving
long lasting protection.
A wood preservative for protection and treatment of lumber against fungal decay and wood
destroying insects including termites
For the Control and Prevention of Common Mildew and Fungus
For Both Interior & Exterior Use
Active Ingredient:
Disodium Octaborate Tetrahydrate………………………...98.0%
(Na2B8O13•4H2O)
Other Ingredients:…………………………………….………….. 2.0%
Total 100.0%
CAUTION
KEEP OUT OF REACH OF CHILDREN
(See Directions for Use and Precautionary Statements on Back [side] Panel)
3-14_080220212
NET WT. 1b. (16 oz. / 453 g) [other sizes permitted]
[Net Wt. 8 oz. (226 g)]
[Net Wt. 2 lbs. (907 g)]
[Net Wt. 4 lbs. (1.81 kg)]
{back label}
PRECAUTIONARY STATEMENTS
Hazards to Humans & Domestic Animals
CAUTION: Harmful if swallowed. Causes moderate eye irritation. Avoid contact with
eyes or clothing. Thoroughly was with soap and water after handling. Remove contaminated
clothing and wash clothing before reuse.
Personal Protective Equipment (PPE)
Some materials that are chemical-resistant to this product are barrier laminate; butyl, nitrile,
neoprene and natural rubbers ≥ 14 mils; polyethylene; polyvinyl chloride; and viton ≥ 14mils.
Applicators, mixers and other handlers must wear long-sleeved shirt, long pants, socks, shoes,
chemical resistant gloves and protective eyewear.
User Safety Requirements
Follow manufacturer’s instructions for cleaning/maintaining PPE. If no such instructions for
washables exist, use detergent and hot water. Keep and wash PPE separately from other
laundry
User Safety Recommendations
Users should:
x Wash hands before eating, drinking, chewing gum, using tobacco or using the toilet;
x Remove clothing/PPE immediately if pesticide gets inside. Then wash thoroughly and
put on clean clothing.
x Remove PPE immediately after handling this product. Wash the outside of gloves
before removing. As soon as possible, wash thoroughly and change into clean clothing
3-14_080220213
FIRST AID
If Swallowed: Call a poison control center or doctor immediately for treatment advice.
Have person sip a glass of water if able to swallow. Do not induce vomiting unless told
to do so by a poison control center or doctor. Do not give anything by mouth to an
unconscious person.
If in Eyes: Hold eye open and rinse slowly and gently with water for 15-20 minutes.
Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye.
Call a poison control center or doctor for treatment advice.
If on Skin or Clothing: Take off contaminated clothing. Rinse skin immediately with
plenty of water for 15-20 minutes. Call a poison control center or doctor for treatment
advice.
---------------------------------------------------------------------------------------------------------------------
Have the product container or label with you when calling a poison control center or
doctor, or going for treatment. You may contact the National Poison Control Center, 1-
800-222-1222, day or night, for emergency medical treatment information.
Environmental Hazards
This pesticide is toxic to fish and wildlife. Do not apply directly to water, to areas where surface
water is present or to intertidal areas below the mean high water mark. Do not contaminate
water by cleaning equipment or disposing
of equipment washwaters.
DIRECTIONS FOR USE
It is a violation of Federal law to use this product in a manner inconsistent with its labeling.
This product is a water soluble, inorganic borate salt with insecticidal and fungicidal properties
effective against wood destroying organisms. Apply this product as a liquid solution. This
product is an effective treatment for wood to kill and prevent infestations of decay fungi. This
product may be used for preventative treatment (before signs of infestation), for wood in
existing structures and for remedial treatment of infested wood in existing structures.
This product is effective for all interior and exterior wood that will be protected from excessive
rain and not in direct contact with the soil. Types of wood include, but are not limited to, all
types of lumber, logs and plywood. Some etching of treated wood may occur from organisms
before they die. Do not apply this product to wood or cellulose material that has been painted,
varnished or sealed. For best results, apply this product to bare wood. Use soap and water to
clean application equipment.
3-14_080220214 Note: Spraying water on some wood species can mobilize natural wood extractives, raise the grain and leave behind calcium or other deposits. Prior to treating large areas, treat a small area with this product solution to ensure that you are satisfied with the final aesthetics. Because of varying conditions affecting use and application, complete prevention of decay by fungi, other organisms or infestations cannot be guaranteed. This product may be used to impart a temporary resistance at these places of attack which may aid in the prevention of immediate reinfestation. Such applications are not a substitute for mechanical alteration, soil treatment or foundation treatment but merely a supplement, particularly where use of other insecticides may pose an odor problem. Use Precautions: Avoid contact with plant life. Harris Termite Powder or solution carelessly spilled or applied to cropland or growing plants, including trees and shrubs, may kill or seriously retard plant growth. IN HOMES/RESIDENTIAL Wood Treatment for wood structures such as decks, fences, steps, sheds, barns and other outbuildings. Preparation of Treatment Solutions 10% Liquid Solution: To prepare solution, add approximately 80% of the required volume of water to the mixing vessel. While stirring, gradually add 1.0 pound of this product for each gallon of treating solution required. Add remaining water to the solution and stir until the entire product has dissolved. Use this solution as soon as possible and do not store for an extended length of time. Liquid Application: Use the liquid solution to control wood destroying organisms, and to kill active infestations of termites, beetles and wood decay fungi. Application may also be made by drilling and then injecting the solution under pressure into sound wood or into the insect galleries of infested wood. For remedial control of wood attacking organisms or for the protection of wood against future infestations, two applications of a 10% liquid solution is recommended. Application Method: Solution can be applied with paint brush, roller or trigger spray bottle. Garden tank sprayer works best for attics, crawl spaces, decks, fences, logs and new construction. Wood surface must be clean, dry and unsealed before treating. Apply solution until wood surface is thoroughly wet. Avoid drilling into plumbing and/or spraying electrical installations. Any white residue can be easily removed or equipment cleaned with warm water and a mild soap solution. Wood should be completely dry (at least 48 hours) before applying paint, varnish or a waterproofing seal. 3-14_08022021
5 When replacing unsound wood: Treat surrounding area and all sides of new wood with 2 applications before installing. USE RESTRICTIONS: Use of this product for the control of bed bugs is prohibited. Applications to carpets are prohibited. Not for use with food contact surfaces, such as wood tables, cutting boards, wood countertops/butcher blocks or other surface meant for food preparation. INSTITUTIONAL/COMMERCIAL Wood Treatment during Construction for Prevention of Wood Destroying Organisms: Spray, foam or dust applications of this product may be made to wood after framing and roofing are in place and before insulation and drywall are installed. Apply this product in liquid solutions to all accessible surfaces of bare wood at a rate of approximately 5 gallons per 1000 square feet [ft2] of wood surface area. Do not spray electrical components or other non-wood components. Treat end-cuts of wood by application methods listed above, or by dipping end-cuts for 1-5 minutes in this product 10% liquid solution. Apply powder at the rate of 0.5 ounce [oz.] [(12-14 grams)] per square foot [ft2] to wall stud areas, box sills, roof eaves, attics and soffits. For treatments in commercial/structural buildings: Do not apply with pressurized application methods except for use with crack, crevice, spot or void treatments. When replacing unsound wood: Treat surrounding area and all sides of new wood with 2 applications before installing. USE RESTRICTIONS: Use of this product for the control of bed bugs is prohibited. Applications to carpets are prohibited. Not for use with food contact surfaces, such as wood tables, cutting boards, wood countertops/butcher blocks or other surface meant for food preparation. Note: Correct leaks and moisture exposure that cause infestation. Wood exposed to moisture should be sealed after treatment. Not recommended for portion of wood that is in direct contact with soil. When gluing wood, treat only after glue is dry. It is recommend to perform a small patch test before general application. 3-14_08022021
6
RESISTANCE MANAGEMENT RECOMMENDATIONS
For resistance management, Harris Termite Powder [this product] contains a Group 8D
insecticide. Any insect population may contain individuals resistant to Harris Termite Powder
[this product] and other Group 8D insecticides. The resistant individuals may dominate the
insect population if this group of insecticides are used repeatedly in the same fields.
Appropriate resistance-management strategies should be followed.
For further information or to report suspected resistance contact P.F Harris Manufacturing at 1-
800-637-0137 or at www.Pfharris.com
STORAGE AND DISPOSAL
Do not contaminate water, food or feed by storage or disposal
STORAGE: Store in a cool, dry area
PESTICIDE DISPOSAL: Wastes resulting from the use of this product may be disposed of on site
or at an approved waste disposal facility.
CONTAINER HANDLING: If empty: Do not reuse this container. Place in trash or offer for
recycling if available. If partly filled: Call your local solid waste agency or 1-800-CLEANUP for
disposal instructions. Never place unused product down any indoor or outdoor drain.
This container is sold by weight, NOT by volume. You can be assured of the proper weight
even though some settling of contents normally occurs during transportation and handling.
Notice: Neither manufacturer nor seller makes any warranty expressed or implied
concerning use of this product other than indicated on label. To the extent consistent
with applicable law, Buyer assumes all responsibility for safety and use not in
accordance with directions.
EPA Reg. No. 3-14
EPA Est. No. 3-GA-1 [multiple]
{Per PR Notice 2007-4, the Batch Code or Lot Number will appear on the container or labeling}
Letter in parenthesis at the end of the EPA Est. No. [indicates manufacturing location and]
corresponds to the first [last] character [letter] in lot number on package [container].
3-14_080220217
Manufactured [for] by:
P.F. Harris Manufacturing Company, LLC
P.O. Box 1922 Cartersville, GA 30120
Questions or Comments? Call 1-800-637-0317
Monday through Friday, 9am to 5pm EST
[Made in the USA]
Product Code:
[ESL REV] [QR Code][Bar Code]
(Note to reviewer: Language in [ ] is optional or interchangeable)
{ } Denotes language that does not appear on the market label(s)
[The following optional graphics/pictograms may appear on the front panel or elsewhere on
sublabels]
3-14_08022021You can also read
