CellClutch S168715 Desktop Application - Quick Installation Guide P2570KA-EN - Apex Tool Group
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
Quick Installation Guide
P2570KA-EN
2021-04
™
CellClutch
S168715
Desktop Application
For additional product information visit our website at www.ClecoTools.comCopyright © Apex Tool Group, 2021
No part of this document may be reproduced in any way or in any form, in whole or in part, or in a natural or
machine-readable language, or transmitted on electronic, mechanical, optical, or other media, without the
express permission of the Apex Tool Group.
Disclaimer
Apex Tool Group reserves the right to modify, supplement, or improve this document or the product without
prior notice.
Trademark
Cleco is a registered trademark of Apex Brands, Inc.
Apex Tool Group
670 Industrial Drive
Lexington, SC 29072
USA
Manufacturer
Apex Tool Group GmbH
Industriestraße 1
73463 Westhausen
Germany
P2570KA | 2021-04 Apex Tool GroupEN
Contents
1 About this document............................................................................. 4
2 Installation ............................................................................................ 5
2.1 System Requirements ................................................................................................. 5
2.2 Installing the software.................................................................................................. 5
3 Operation.............................................................................................. 7
3.1 Product Information ..................................................................................................... 7
3.2 General Settings.......................................................................................................... 8
3.3 Advanced Settings ...................................................................................................... 9
3.4 Tool Actions ................................................................................................................. 9
3.5 Application Settings ................................................................................................... 11
3.6 Menu Bar ................................................................................................................... 12
Apex Tool Group P2570KA | 2021-04 31 About this document
EN
1 About this document
This document contains instructions and notes:
• for safe, appropriate and effective handling of the product.
• for installation, configuration and function.
• for programming the software.
Software version: S168715-0.9.5.
The original language of this document is English.
Symbols in the text
italic Menu options (e.g.,Diagnostics) input fields, check boxes, radio buttons or dropdown
menus.
> Indicates selection of a menu option from a menu, e.g., File > Print
Specifies switches, pushbuttons or the keys of an external keyboard, e.g.,
Courier Filenames and paths, e.g., setup.exe
• List
- List, level 2
a) Options
b)
→ Result
1. (...) Action steps
2. (...)
Single action step
4 P2570KA | 2021-04 Apex Tool GroupInstallation
2
EN
2 Installation
2.1 System Requirements
• Windows 10 64-Bit
• Screen resolution of 1280 x 800 or higher recommended
2.2 Installing the software
The software is delivered in the form of an executable installation package.
1. Download the software package CellClutch
from the website:
https://software.apextoolgroup.com/current-
software-packages/cellclutch/
2. Start the installation file
CellClutch-X.Y.Z.exe.
3. Select a language and press .
4. Press to start the installation.
5. Select the installation folder and press .
Apex Tool Group P2570KA | 2021-04 52 Installation
EN
6. Select components to be installed and press
.
7. Press .
8. Confirm the installation with before it
starts.
6 P2570KA | 2021-04 Apex Tool GroupOperation
3
EN
3 Operation
The current software is a beta version. Functions can still change until the final release.
The user interface is divided into three parts. On the left are global settings and actions, in the middle are
forward application settings, and on the right are reverse application settings:
Fig. 3-1: User interface with exemplary settings
The individual panes of the user interface are described below.
3.1 Product Information
In this pane information about the tool is displayed.
Fig. 3-2: Product Information
Parameter Description
Model This read-only field shows the model name of the tool. If no tool is con-
nected, Not Connected is displayed. If no model name is stored in the con-
nected tool, Not available is displayed.
ID This read-only field shows the ID of the tool. If no tool is connected, Not
Connected is displayed. If no ID is stored in the connected tool, Not avail-
able is displayed.
Apex Tool Group P2570KA | 2021-04 73 Operation
EN
Parameter Description
Serial Number This read-only field shows the serial number of the tool. If no tool is con-
nected, Not Connected is displayed. If no serial number is stored in the con-
nected tool, Not available is displayed.
Revision This field shows the software version of the tool.
Note This field allows to store a remark in the tool.
3.2 General Settings
General settings can be made in this pane.
Fig. 3-3: General Settings - View of the default settings
Parameter Description
Enable Rotation It is possible to set which direction of rotation should be active: Only for-
ward, only reverse or both. If forward is selected, the reverse program can-
not be used, and vice versa.
Work Light The brightness of the work light can be configured.
Status Light The status light can be turned on or off.
Buzzer The buzzer can be turned on or off.
Brake If the brake is active, the motor brakes as soon as the trigger is released,
otherwise the motor coasts.
The dark gray buttons indicate the selected option, while the light gray ones show the unselected ones.
Status display
The color of the LEDs indicates the status of the rundown and tool.
Message Color Worklight Color Status Buzzer
OK result Continuous green light Continuous green light
NOK result Continuous red light Continuous red light x
Cross thread detection Continuous red light Continuous red light x
Rehit Protection / Dou- Continuous red light Continuous red light x
ble Hit
During batch Continuous green light Continuous blue light
Batch OK (single result) - Continuous green light
Batch OK (completed) Continuous green light Flashing light green and blue x
Batch NOK (completed) Continuous red light Continuous red and blue light
Tool overheating Flashing light red Flashing light red
Maintenance alarm - Flashing light red - blue -
green
Battery low Flashing light red - blue Flashing light red - blue
→ Tool stops auto-
matically
8 P2570KA | 2021-04 Apex Tool GroupOperation
3
EN
Message Color Worklight Color Status Buzzer
Check of the LED indica- Flashing light red - blue - Flashing light red - blue - x
tor, light and buzzer green green
during first install battery
operation.
3.3 Advanced Settings
Some advanced settings can be made in this pane.
Fig. 3-4: Advanced Settings
Parameter Description
Restart Delay The restart delay can be configured here. This means the minimum time
between a clutch event and the start of the next run.
Double Hit Double hit protection can be activated and configured here.
A second clutch event within the double hit time automatically leads to a
NOK indication. This is to detect a tightening that has already been tight-
ened by the previous run.
Gear Translation The gear translation ratio configured in the tool is displayed here. Please
note that the value can currently only be read at this point.
3.4 Tool Actions
Some tool actions can be made in this pane.
Fig. 3-5: Tool Actions
Apex Tool Group P2570KA | 2021-04 93 Operation
EN
Parameter Description
Connect (Serial Port) Connect to a tool via a virtual serial port (USB). The following dialog
appears:
Select the COM port to which the tool is connected and click OK. If
Read Settings is selected, the settings (global and application settings)
are read automatically after the connection is established.
Reconnect Reestablish the connection. If there is no connection at the moment, the last
existing connection will be re-established.
Disconnect Disconnect current connection.
Read Settings Read settings (global and application settings) from the currently connected
tool.
Write Settings Write settings (global and application settings) to the currently connected
tool.
Download results Download tightening results from the currently connected tool. The following
dialog appears:
Select the file format and click OK. After that another dialog appears to
select the target file.
Catalog Data Shows technical data of the tool.
10 P2570KA | 2021-04 Apex Tool GroupOperation
3
EN
Parameter Description
Service Information Displays service information from the tool.
Firmware Update To perform a firmware update on the tool:
1. Press and hold the start switch on the tool and connect the tool to the
PC via a Micro-B USB cable.
2. There are three ways to start the firmware update:
- Start the CellClutch software and press .
- Start the desktop shortcut CellClutch Firmware Update. This is only
possible if the desktop shortcut was activated during installation.
- Start CellClutch Firmware Update on the PC under Start > Apex
Tool Group.
→ The upgrade.bat file opens in the Command Prompt window and
the update is started automatically.
→ The update is finished when Upgrade successful is displayed in the
Command Prompt window.
3.5 Application Settings
It is possible to set separate tightening programs for forward and reverse operation.
Fig. 3-6: Example Stage 1
The pre-tightening stages 1-5 and the After Clutch Stage can be configured this way:
Parameter Description
Stage X With the checkbox in the pane title it is possible to disable the stage com-
pletely. In this case the pane will be collapsed.
Rotation The direction of rotation can be set to either forward or reverse.
Speed The rotation speed can be set here.
Condition The condition when the stage is completed can be selected. Either the
angle of rotation or the duration is monitored.
Angle/Duration Depending on which condition is selected, the angle or the time can be set
here.
The Tightening Stage can be configured this way:
Parameter Description
Tightening Stage This stage cannot be disabled because it is mandatory.
Rotation The direction of rotation is always forward in this stage. It cannot be
changed.
Speed The rotation speed can be set here.
Apex Tool Group P2570KA | 2021-04 113 Operation
EN
Parameter Description
Limit Type Here you can set whether the angle or the duration is limited during tighten-
ing.
Angle/Duration Limit Depending on which limit type is selected, the angle or the time can be set
here.
In the reverse operation mode no Tightening Stage and no After Clutch Stage is available. However, at
least one stage must be active in reverse operation mode.
3.6 Menu Bar
The menu bar offers several useful menus:
Menu Function
File • Open: Load the settings from a file.
• Save as: Save the settings to a file.
• Preferences: Provides options to configure the App:
- Automatically connect on startup: If this option is selected, a connection to the
last connected tool is established at startup.
- Read settings after automatic connect: If this option is selected, after the auto-
matic connection establishment the settings are read from the tool.
• Exit: Close the App.
Edit • Undo: Undo the last change to the settings.
• Redo: Restore the next change to the settings (Undo the last undo).
Tool The tool menu offers the same functions as the tool actions pane described above.
Language Change the user interface language.
Help • Open Log Directory: Open the directory where log files are stored.
• Open Latest Log File: Open the latest log file with the system's default text editor.
• Open Source Licenses: Shows the open source licenses used in the software.
• About: Shows information about the software.
12 P2570KA | 2021-04 Apex Tool GroupPOWER TOOLS SALES & SERVICE CENTERS
Please note that all locations may not service all products.
Contact the nearest Cleco® Sales & Service Center for the appropriate facility to handle your service
requirements.
Sales Center
Service Center
NORTH AMERICA | SOUTH AMERICA
DETROIT, MICHIGAN LEXINGTON, MEXICO BRAZIL
Apex Tool Group SOUTH CAROLINA Apex Tool Group Apex Tool Group
2630 Superior Court Apex Tool Group Vialidad El Pueblito #103 Av. Liberdade, 4055
Auburn Hills, MI 48236 670 Industrial Drive Parque Industrial Querétaro Zona Industrial Iporanga
Phone: +1 (248) 393-5644 Lexington, SC 29072 Querétaro, QRO 76220 Sorocaba, São Paulo
Fax: +1 (248) 391-6295 Phone: +1 (800) 845-5629 Mexico CEP# 18087-170
Phone: +1 (919) 387-0099 Phone: +52 (442) 211 3800 Brazil
Fax: +1 (803) 358-7681 Fax: +52 (800) 685 5560 Phone: +55 15 3238 3870
Fax: +55 15 3238 3938
EUROPE | MIDDLE EAST | AFRICA
ENGLAND FRANCE GERMANY HUNGARY
Apex Tool Group GmbH Apex Tool Group SAS Apex Tool Group GmbH Apex Tool Group
C/O Spline Gauges 25 Avenue Maurice Chevalier - Industriestraße 1 Hungária Kft.
Piccadilly, Tamworth ZI 73463 Westhausen Platánfa u. 2
Staffordshire B78 2ER 77330 Ozoir-La-Ferrière Germany 9027 Györ
United Kingdom France Phone: +49 (0) 73 63 81 0 Hungary
Phone: +44 1827 8727 71 Phone: +33 1 64 43 22 00 Fax: +49 (0) 73 63 81 222 Phone: +36 96 66 1383
Fax: +44 1827 8741 28 Fax: +33 1 64 43 17 17 FAX: +36 96 66 1135
ASIA PACIFIC
AUSTRALIA CHINA INDIA JAPAN KOREA
Apex Tool Group Apex Power Tool Trading Apex Power Tool India Apex Tool Group Japan Apex Tool Group Korea
519 Nurigong Street, Albury (Shanghai) Co., Ltd. Private Limited Korin-Kaikan 5F, #1503, Hibrand Living Bldg.,
NSW 2640 2nd Floor, Area C Gala No. 1, Plot No. 5 3-6-23 Shibakoen, Minato- 215 Yangjae-dong,
Australia 177 Bi Bo Road S. No. 234, 235 & 245 Ku, Seocho-gu, Seoul 137-924,
Phone: +61 2 6058 0300 Pu Dong New Area, Shanghai Indialand Global Tokyo 105-0011, JAPAN Korea
China 201203 P.R.C. Industrial Park Phone: +81-3-6450-1840 Phone: +82-2-2155-0250
Phone: +86 21 60880320 Taluka-Mulsi, Phase I Fax: +81-3-6450-1841 Fax: +82-2-2155-0252
Fax: +86 21 60880298 Hinjawadi, Pune 411057
Maharashtra, India
Phone: +91 020 66761111
Apex Tool Group, LLC
Phone: +1 (800) 845-5629
Phone: +1 (919) 387-0099
Fax: +1 (803) 358-7681
www.ClecoTools.com
0421 | Cleco® is a registered trademark of Apex Brands, Inc. | © 2021 www.ClecoTools.deYou can also read
