GET STARTED! - www.arrma-rc.com - SPEKTRUM SLT3 Transmitter - Horizon Hobby

Page created by Dorothy Burton
 
CONTINUE READING
GET STARTED!
                    SPEKTRUM
                          SLT3
                    Transmitter

     ARRMA 4x4 3S
     BLX Vehicle

                         REQUIRED:
                         4x AA Batteries
                         LiPo Battery
                         (1x2S or 1x3S)
                         LiPo Charger

www.arrma-rc.com
Warnings
                				NOTICE
                All instructions, warranties and other collateral documents are subject to change at the sole
                discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com or
                www.towerhobbies.com and click on the support or resources tab for this product.

                                          MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating
this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and
serious injury OR create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a
possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no
possibility of injury.

        WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure
        to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic
mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or
other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible compo-
nents or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for
safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly,
setup or use, in order to operate correctly and avoid damage or serious injury.

       Age Recommendation: Not for children under 14 years. This is not a toy.
                                SAFETY PRECAUTIONS AND WARNINGS
 As the user of this product, you are solely responsible for              the reach of children.
 operating in a manner that does not endanger yourself and              • Never lick or place any portion of the model in your
 others or result in damage to the product or property of                 mouth as it could cause serious injury or even death.
                                                                        • Exercise caution when using tools and sharp
 others.
                                                                          instruments.
 This model is controlled by a radio signal subject to interfer-        • Take care during maintenance as some parts may have
 ence from many sources outside your control. This interfer-              sharp edges.
                                                                        • Immediately after using your model, do NOT touch
 ence can cause momentary loss of control, so it is advisable
                                                                          equipment such as the motor, electronic speed control
 to always keep a safe distance in all directions around your             and battery, because they generate high temperatures.
 model as this margin will help avoid collisions or injury.               You may burn yourself seriously by touching them.
 • Never operate your model with low transmitter batteries.             • Do not put fingers or any objects inside rotating and
 • Always operate your model in open spaces away from                     moving parts, as this may cause damage or serious
   full-size vehicles, traffic and people.                                injury.
 • Never operate the model in the street or in populated                • Always turn on your transmitter before you turn on
   areas for any reason.                                                  the car. Always turn off the car before turning your
 • Carefully follow the directions and warnings for this and              transmitter off.
   any optional support equipment (chargers, rechargeable               • Keep the wheels of the model off the ground when
   battery packs, etc.) you use.                                          checking the operation of the radio equipment.
 • Keep all chemicals, small parts and anything electrical out of

                                                                    2                                   WWW.ARRMA-RC.COM
WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer
                  to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with
         regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM
         or Spektrum technology.

                  WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
     Your new Horizon Hobby vehicle has been designed and built                 contact with salt water (ocean water or water on salt-
     with a combination of                                                      covered roads), contaminated or polluted water. Salt water
     waterproof and water-resistant components to allow you                     is very conductive and highly corrosive, so use caution.
     to operate the product in many “wet conditions,” including               • Even minimal water contact can reduce the life of your
     puddles, creeks, wet grass, snow and even rain.                            motor if it has not been certified as water-resistant or
     While the entire vehicle is highly water-resistant, it is not com-         waterproof. If the motor becomes excessively wet, apply
     pletely waterproof and your vehicle should NOT be treated                  very light throttle until the water is mostly removed from
     like a submarine. The various electronic components used                   the motor. Running a wet motor at high speeds may
     in the vehicle, such as the Electronic Speed Control (ESC),                rapidly damage the motor.
     servo(s) and receiver are waterproof, however, most of the               • Driving in wet conditions can reduce the life of the motor.
     mechanical components are water-resistant and should not                   The additional resistance of operating in water causes
     be submerged.                                                              excess strain. Alter the gear ratio by using a smaller
                                                                                pinion or larger spur gear. This will increase torque (and
     Metal parts, including the bearings, hinge pins, screws and                motor life) when running in mud, deeper puddles, or any
     nuts, as well as the contacts in the electrical cables, will               wet conditions that will increase the load on the motor for
     be susceptible to corrosion if additional maintenance is                   an extended period of time.
     not performed after running in wet conditions. To maximize
     the long-term performance of your vehicle and to keep                    Wet Conditions Maintenance
     the warranty intact, the procedures described in the “Wet
     Conditions Maintenance” section below must be performed                  • Remove the battery pack(s) and dry the contacts. If you
     regularly if you choose to run in wet conditions. If you are               have an air compressor or a can of compressed air, blow
     not willing to perform the additional care and maintenance                 out any water that may be inside the recessed connector
     required, then you should not operate the vehicle in those                 housing.
     conditions.                                                              • Remove the tires/wheels from the vehicle and gently rinse
                                                                                the mud and dirt off with a garden hose. Avoid rinsing the
                                                                                bearings and transmission.
                CAUTION: Failure to exercise caution while using
                  this product and complying with the following                NOTICE: Never use a pressure washer to clean your
         precautions could result in product malfunction and/or void           vehicle.
         the warranty.                                                        • Use an air compressor or a can of compressed air to dry
                                                                                the vehicle and help remove any water that may have
     General Precautions                                                        gotten into small crevices or corners.
     •     Read through the wet conditions maintenance procedures             • Spray the bearings, drive train, fasteners and other metal
           and make sure that you                                               parts with a water-displacing light oil or lubricant. Do not
           have all the tools you will need to properly maintain your           spray the motor.
           vehicle.                                                           • Let the vehicle air dry before you store it. Water (and oil)
                                                                                may continue to drip for a few hours.
     •     Not all batteries can be used in wet conditions. Consult           • Increase the frequency of disassembly, inspection and
           the battery manufacturer before use. Caution should be               lubrication of the following:
           taken when using Li-Po batteries in wet conditions.                    • Front and rear axle hub assembly bearings.
     •     Most transmitters are not water-resistant. Consult                     • All transmission cases, gears and differentials.
           your transmitter’s manual or the manufacturer before                   • Motor—clean with an aerosol motor cleaner and
           operation.                                                                 re-oil the bearings with lightweight motor oil.
                                                                              • Drain any water that has collected in the tires by spinning
     •     Never operate your transmitter or vehicle where lightning             them at high speed. With the body removed, place the
           may be present.                                                       vehicle upside down and pull full throttle for a few short
     •     Do not operate your vehicle where it could come in                    bursts until the water has been removed.

OM                                                                        3                                   WWW.ARRMA-RC.COM
Warnung
              				HINWEIS
              Alle Anweisungen, Garantien und dazugehörigen Dokumente können ohne Ankündigung von Horizon
              Hobby, LLC geändert werden. Eine aktuelle Version ersehen Sie bitte im Support Feld unter:
              http://www.horizonhobby.com / http://www.towerhobbies.com

                                              ERKLÄRUNG DER BEGRIFFE
 Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahrenrisiken beim Betrieb
 dieses Produkts hinzuweisen:
 WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,
 Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberflächliche Verletzungen.
 ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die
 Gefahr von schweren Verletzungen.
 HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe oder
 keine Gefahr von Verletzungen ergeben.

       WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen vertraut
       zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem Eigentum
führen oder schwere Verletzungen verursachen.
Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben werden
und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und verantwortungsvolle
Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten führen. Verwenden Sie das
Produkt nicht mit inkompatiblen Komponenten oder verändern es in jedweder Art ausserhalb der von Horizon Hobby, LLC
vorgegebenen Anweisungen. Diese Bedienungsanleitung enthält Anweisungen für Sicherheit, Betrieb und Wartung. Es ist
unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung alle Anweisungen und Warnhinweise im Handbuch
zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben werden kann und Schäden oder schwere Verletzungen
vermieden werden.

           Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug.

                            SICHERHEITSHINWEISE UN WARNUNGEN
Als Nutzer dieses Produktes, sind Sie allein verantwortlich,         Bauteile aus der Reichweite von Kindern.
es in einer Art und Weise zu benutzen, die eine eigene Ge-         • Lecken Sie niemals an Teilen von Ihrem Modell oder
fährdung und die anderer oder Beschädigung an anderem                nehmen diese in den Mund, da diese Sie ernsthaft
                                                                     verletzten oder töten können.
Eigentum ausschließt.
                                                                   • Seien Sie immer aufmerksam wenn Sie Werkzeug oder
Das Modell ist ferngesteuert und anfällig für bestimmte              scharfe Instrumente verwenden.
äußere Einflüsse. Diese Einfl üsse können zum vorüberge-           • Seien Sie bei dem Bau vorsichtig, da einige Teile scharfe
henden Verlust der Steuerfähigkeit führen, so dass es immer          Kanten haben könnten.
                                                                   • Fassen Sie bitte unmittelbar nach dem Betrieb nicht
sinnvoll ist genügend Sicherheitsabstand in alle Richtungen
                                                                     den Motor, Regler oder Akku an, da diese Teile sich
um das Modell zu haben.                                              sehr erwärmen können und Sie sich bei dem berühren
• Fahren Sie das Modell nie mit fast leeren oder                     ernsthaft verbrennen können.
   schwachen Senderbatterien.                                      • Fassen Sie nicht in drehende oder sich bewegende Teile,
• Betreiben Sie Ihr Modell stets auf offenen Geländen, weit          da sich sich ernsthaft dabei verletzen können.
   ab von Automobilen, Verkehr und Menschen.                       • Schalten Sie immer zuerst den Sender ein, bevor Sie
• Fahren Sie Ihr Modell nicht auf der Straße oder belebten           den Empfänger im Fahrzeug einschalten.
   Plätzen.                                                        • Stellen Sie das Fahrzeug mit den Rädern nicht auf den
• Beachten Sie vorsichtig alle Hinweise und Warnungen                Boden, wenn Sie die Funktionen überprüfen.
   für das Modell und allen dazu gehörigen Equipment.
• Halten Sie alle Chemikalien, Kleinteile und elektrische

                                                               4                                 WWW.ARRMA-RC.COM
WARNUNG GEGEN GEFÄLSCHTE PRODUKTE: Sollten Sie jemals eine Spektrum Komponente ersetzen wollen,
               kaufen Sie die benötigen Ersatzteile immer bei Horizon Hobby oder einem von Horizon hobby autorisiertem Händler
      um die hohe Qualität des Produktes zu gewährleisten. Horizon Hobby LLC lehnt jedwede Haftung, Garantie oder
      Unterstützung sowie Kompatibilitäts- oder Leistungsansprüche zu DSM oder Spektrum in Zusammenhang mit gefälschten
      Produkten ab.

        WASSERFESTES FAHRZEUG MIT SPRITZWASSERGESCHÜTZER ELEKTRONIK
     Y neues Horizon Hobby Fahrzeug wurde mit einer                     und stark korrosionsfördernd, sein Sie daher sehr
     Kombination von wasserfesten und spritzwassergeschützen            achtsam.
     Komponenten ausgestattet, die den Betrieb des Fahrzeuges         • Schon geringer Wasserkontakt kann den Motor
     unter nassen Bedingungen inklusive Pfützen, Bächen,                beschädigen wenn er nicht für den Betrieb in Wasser
     nassem Gras, Schnee oder sogar Regen ermöglichen.                  ausgelegt ist. Sollte der Motor nass geworden sein geben
                                                                        Sie etwas Gas bis die meiste Feuchtigkeit vom Motor
     Obwohl das Fahrzeug sehr wasserfest ausgelegt ist, ist             entfernt ist. Lassen Sie einen nassen Motor auf hoher
     es nicht vollständig wasserdicht und sollte NICHT wie ein          Geschwindigkeit laufen wird dieses den Motor sehr
     U-Boot behandelt werden. Etliche in diesem Fahrzeug                schnell beschädigen.
     eingesetzte elektronische Komponenten sind wasserdicht,          • Fahren in nasser Umgebung kann die Lebenszeit
                                                                        des Motors reduzieren, da dieses den Motor stark
     wie der Fahrtregler und das Servos. Die mechanischen
                                                                        beansprucht. Verändern Sie die Untersetzung
     Komponenten sind jedoch nur wasserabstoßend und sollten          • zu einem kleinerem Ritzel oder größeren Zahnrad.
     deshalb nicht untergetaucht werden.                                Dieses erhöht das Drehmoment (und verlängert die
     Metallteile, inklusive Lager, Bolzen Schrauben und Muttern         Motorlebensdauer) bei dem Betrieb in Matsch, tieferen
                                                                        Pfützen oder anderen Bedingungen, die die Last des
     wie auch die Kontakte in den elektrischen Kabeln sind
                                                                        Motors für einen längeren Zeitraum erhöhen.
     für Korrosion anfällig wenn nicht zusätzliche Wartung
     nach jedem Betrieb in feuchter/nasser Umgebung                   Wartungsanleitung nach Fahrten in nasser Umgebung
     erfolgt. Um die Langzeitleistung und die Garantie ihres          • Entfernen Sie die Akkupacks und trocknen die Kontakte.
     Fahrzeuges zu erhalten müssen Sie die Wartung wie in               Sollten Sie einen Kompressor oder Druckluft zur
     der Wartungsanleitung nach Fahrten in nasser Umgebung              Verfügung haben, blasen Sie damit das Wasser aus dem
     beschrieben durchführen. Sollten Sie diese zusätzliche             Motorgehäuse.
                                                                      • Nehmen Sie die Reifen und Felgen vom Fahrzeug ab und
     Wartung nicht ausführen wollen, dürfen Sie ihr Fahrzeug
                                                                        spülen vorsichtig Sie mit einem Gartenschlauch ab.
     unter diesen Bedingungen nicht betreiben.
                                                                       HINWEIS: Verwenden Sie keinen Hochdruckreiniger um
              ACHTUNG: Unaufmerksamkeit während des                    das Fahrzeug zu reinigen.
               Betriebes des Produktes in Zusammenhang mit
                                                                      • Reinigen Sie das Fahrzeug mit Druckluft aus einem
      den folgenden Sicherheitshinweisen kann zu                        Kompressor oder einer Druckluftflasche und entfernen so
      Fehlfunktionen und dem Verlust der Garantie führen.               das Wasser aus den Spalten und Ecken.
                                                                      • Sprühen Sie alle Lager, Befestigungen und andere
     Allgemeine Sicherheitshinweise
                                                                        Metallteile mit einem wasserverdrängendem Leichtöl oder
     • Bitte lesen Sie sich die Wartungsanleitung nach Fahrten          Schmiermittel ein. Sprühen Sie nicht den Motor ein.
       in nasser Umgebung sorgfältig durch und stellen                • Lassen Sie das Fahrzeug vor dem Einlagern vollständig
       sicher, dass Sie alle Werkzeuge für eine Wartung des             trocknen. Das Abtropfen von Wasser (und Öl) kann
       Fahrzeuges haben.                                                durchaus ein paar Stunden dauern.
     • Sie können nicht alle Akkutypen für Fahrten in nasser          • Erhöhen Sie die Wartungsintervalle (Demontage,
       Umgebung nutzen. Fragen Sie dazu vor dem Einsatz den             Inspektion und schmieren) von folgenden Komponenten:
       Hersteller des Akkus. Verwenden Sie keine LiPo Akkus in             • Vorder- und Hinterachse, Aufnahme und Lager.
       nasser Umgebung.                                                    • Alle Antriebswellen Lager, Gehäuse, Getriebe und
     • Der enthaltene Sender ist weder wasserabweisend noch                  Differentiale.
       wasserdicht. Wenn Sie einen anderen Sender verwenden                • Motor: reinigen Sie den Motor mit einen Aerosol
       wollen, prüfen Sie die Anleitung für diesen Sender oder               Reiniger und ölen
       fragen Sie beim Hersteller nach.                                      Sie dann die Lager mit leichtem Motoröl.
     • Nehmen Sie niemals den Sender bei Blitzen oder                 • Entfernen Sie Wasser in den Reifen durch Gas geben.
       Gewitter in Betrieb.                                              Nehmen Sie die Karosserie ab, drehen das Fahrzeug auf
     • Betreiben Sie ihr Fahrzeug nicht an Orten wo es in                den Kopf und geben ein paar Mal kurz Vollgas bis das
       Kontakt mit Salzwasser oder verschmutzten, belasteten             Wasser aus dem Reifen entfernt ist.
       Gewässern kommen kann. Salzwasser ist sehr leitend

OM                                                                5                                 WWW.ARRMA-RC.COM
Avertissements
               				REMARQUE
               Toutes les instructions, garanties et autres documents de garantie sont sujets à modification à la seule
               discrétion de Horizon Hobby, LLC. Veuillez, pour une documentation produit bien à jour, visiter le site internet
 		            http://www.horizonhobby.com / http://www.towerhobbies.com.

                                         SIGNIFICATION DE CERTAINS MOTS
 Les termes suivants servent, tout au long de la littérature produits, à désigner différents niveaux de blessures potentielles
 lors de l’utilisation de ce produit:
 AVERTISSEMENT : procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels,
 des dommages collatéraux et des blessures graves OU engendrer une probabilité élevée de blessure superficielle.
 ATTENTION : procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET des
 blessures graves.
 REMARQUE : procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET
 éventuellement un faible risque de blessures.

         AVERTISSEMENT : Lisez la TOTALITE du manuel d’utilisation afin de vous familiariser avec les caractéristiques du
         produit avant de le faire fonctionner. Une utilisation incorrecte du produit peut avoir comme résultat un
endommagement du produit lui-même, celui de propriétés personnelles voire entraîner des blessures graves.
Ceci est un produit de loisirs perfectionné et NON PAS un jouet. Il doit être manipulé avec prudence et bon sens et requiert
quelques aptitudes de base à la mécanique. L’incapacité à manipuler ce produit de manière sûre et responsable peut
provoquer des blessures ou des dommages au produit ou à d’autres biens. Ce produit n’est pas destiné à être utilisé par
des enfants sans la surveillance directe d’un adulte. N’essayez pas de modifier ou d’utiliser ce produit avec des composants
incompatibles hors des instructions fournies par Horizon Hobby, LLC. Ce manuel comporte des instructions de sécurité,
d’utilisation et d’entretien. Il est capital de lire et de respecter toutes les instructions et avertissements du manuel avant
l’assemblage, le réglage ou l’utilisation afin de le manipuler correctement et d’éviter les dommages ou les blessures graves.

                                  14 ans et plus. Ceci n’est pas un jouet.

               PRÉCAUTIONS ET AVERTISSEMENTS LIÉS À LA SÉCURITÉ
En tant qu’utilisateur de ce produit, il est de votre seule           packs de batteries rechargeables, etc.) que vous utilisez.
responsabilité de le faire fonctionner d’une manière qui            • Tenez tous les produits chimiques, les petites pièces
ne mette en danger ni votre personne, ni de tiers et qui              et les composants électroniques hors de portée des
                                                                      enfants.
ne provoque pas de dégâts au produit lui-même ou à la
                                                                    • Ne léchez ni ne mettez jamais en bouche quelque partie
propriété d’autrui.                                                   de votre modèle que ce soit, afin d’éviter tout risque de
Ce modèle est contrôlé par un signal radio, qui peut être             blessures graves, voire danger de mort.
soumis à des interférences provenant de nombreuses                  • Faites bien attention lors de l’utilisation d’outils et lors de
                                                                      l’utilisation d’instruments coupants.
sources hors de votre contrôle. Ces interférences peuvent
                                                                    • Faites bien attention lors du montage, certaines pièces
provoquer une perte momentanée de contrôle. Il est donc               peuvent avoir des bords coupants.
conseillé de garder une bonne distance de sécurité tout             • Après avoir utilisé votre modèle, NE touchez PAS à
autour de votre modèle, ce qui aidera à éviter les collisions         certaines de ces pièces telles que le moteur, le contrôleur
ou les blessures.                                                     électronique de vitesse et la batterie, car elles peuvent
                                                                      encore se trouver à des températures élevées. Vous
• Ne faites jamais fonctionner votre modèle lorsque les
                                                                      risquez de vous brûler gravement en cas de contact avec
  batteries de l’émetteur sont faibles.
                                                                      elles.
• Faites toujours fonctionner votre modèle dans une zone
                                                                    • Ne mettez ni vos doigts ni aucun autre objet entre des
  dégagée, à l’écart des voitures, de la circulation ou de
                                                                      pièces en rotation ou en mouvement, vous risqueriez des
  personnes.
                                                                      dommages ou des blessures graves.
• Ne faites jamais et pour quelque raison que ce soit
                                                                    • Allumez toujours votre émetteur avant d’allumer le
  fonctionner votre modèle dans la rue ou dans des zones
                                                                      récepteur du véhicule. Éteignez toujours le récepteur
  habitées.
                                                                      avant d’éteindre votre émetteur.
• Respectez scrupuleusement les instructions et
                                                                    • Veillez à ce que les roues du modèle ne soient pas
  avertissement à cet effet ainsi que pour tous les
                                                                      en contact avec le sol lorsque vous contrôlez le
  équipements optionnels/complémentaires (chargeurs,
                                                                      fonctionnement de votre équipement radio.

                                                                6                                    WWW.ARRMA-RC.COM
ATTENTION aux contrefaçons. Nous vous remercions d’avoir acheté un véritable produit Spektrum. Toujours
               acheter chez un revendeur officiel Horizon hobby pour être sur d’avoir des produits authentiques. Horizon Hobby
      décline toute garantie et responsabilité concernant les produits de contrefaçon ou les produits se disant compatibles DSM ou
      Spektrum.

         VÉHICULE RÉSISTANT À L’EAU ÉQUIPÉ D’UNE ÉLECTRONIQUE ÉTANCHE
     Votre nouveau véhicule Horizon Hobby a été conçu et                     sur une route salée), ou de l’eau polluée ou contaminée.
     fabriqué en combinant des composants étanches et des                  • Une petite quantité d’eau peut réduire la durée de vie
     composant résistants à l’eau vous permettant d’utiliser ce              du moteur s’il n’est pas certifié étanche ou résistant aux
                                                                             projections d’eau. Si le moteur devient excessivement
     produit dans plusieurs “Conditions Humides” incluant les
                                                                             humide, appliquez légèrement les gaz pour évacuer le
     flaques d’eau, les ruisseaux, l’herbe humide, la neige et               maximum d’eau du moteur. Faire tourner à un régime
     même la pluie.                                                          élevé un moteur humide causerait son endommagement
     Bien que le véhicule possède une grande résistance vis à vis            rapide.
                                                                           • L’utilisation en conditions humides peut réduire la durée
     de l’eau, il n’est pas entièrement étanche et votre véhicule ne
                                                                             de vie de vie du moteur. La résistance de l’eau cause des
     doit PAS être utilisé comme un sous-marin. Les composants               efforts plus importants. Adaptez le rapport de transmission
     électroniques utilisés sur ce véhicule comme le variateur               en utilisant un pignon plus petit ou une couronne plus
     électronique et le servo sont étanches, cependant, la majorité          grande. Cela augmentera le couple (et la durée de vie du
     des éléments mécaniques est résistante à l’eau mais ne doit             moteur) quand vous roulez dans la boue, dans les flaques
                                                                             profondes ou n’importe quelle autre condition humide,
     pas être immergée.
                                                                             cela augmente la charge appliquée au moteur.
     Les pièces métalliques comme les roulements, les axes de
     suspension, les vis et les écrous ainsi que les contacts des          Maintenance en conditions humides
     prises des câbles électriques sont exposés à l’oxydation              • Retirez la batterie et séchez ses contacts. Si vous
     si vous n’effectuez un entretien supplémentaire après                   possédez un compresseur d’air ou une bombe d’air
     avoir utilisé le produit dans des conditions humides. Pour              compressé, chassez toute l’humidité qui se trouve dans
     conserver à long terme les performances de votre véhicule               la prise.
                                                                           • Retirez les roues du véhicule et rincez-les à l’aide d’un
     et conserver la garantie, les procédures décrites dans la               arrosoir pour retirer la boue et la poussière. Evitez de
     section « Maintenance en conditions humides » doivent être              rincer les roulements et la transmission.
     régulièrement effectuées si vous roulez dans des conditions
                                                                            REMARQUE : N’utilisez jamais un nettoyeur haute pression
     humides. Si vous ne souhaitez pas effectuer la maintenance
                                                                            pour nettoyer le véhicule.
     supplémentaire requise, n’utilisez pas le véhicule dans ces
     conditions.                                                           • Utilisez un compresseur d’air ou une bombe d’air
                                                                             compressée pour sécher le véhicule et vous aider à retirer
              ATTENTION : Un défaut de soin durant l’utilisation             l’eau logée dans les renfoncements et les recoins.
                et un non-respect des consignes suivantes peut             • Vaporisez du lubrifiant ou de l’anti-humidité sur les
      entraîner un dysfonctionnement du produit et/ou annuler la             roulements, les vis ou autres pièces métalliques. Ne pas
                                                                             en vaporiser sur le moteur.
      garantie.
                                                                           • Laissez le véhicule sécher avant de le stocker. L’eau (et
                                                                             l’huile) peuvent continuer à s’écouler durant quelques
     Précautions générales
                                                                             heures.
     • Lisez avec attention les procédures de maintenance en               • Augmentez la fréquence d’inspection, de démontage et
       conditions humides et vérifiez que vous possédez tous                 de lubrification des éléments suivants :
       les outils nécessaires pour effectuer la maintenance du                   • Les axes de roues et roulements des fusées avant
       véhicule.                                                                    et arrière.
     • Toutes les batteries ne peuvent être utilisées en                         • Tous les boitiers de transmissions, pignons et
       conditions humides. Consultez la documentation du                            différentiels.
       fabricant de votre batterie avant utilisation. N’utilisez pas             • Le moteur—nettoyez-le à l’aide d’un aérosol de
       des batteries Li-Po dans des conditions humides.                             nettoyant moteur et lubrifiez les paliers à l’aide de
     • L’émetteur inclus n’est ni étanche ni résistant à l’eau.                     lubrifiant pour roulements.
       Si vous utilisez un émetteur différent que celui inclus,            • Evacuez l´eau collectée par les pneus en les faisant
       consultez le manuel de l’émetteur ou prenez contact avec                tourner à haute vitesse. Retirez la carrosserie, retournez
       son fabricant avant utilisation.                                        le véhicule et donnez des courts coups d´accélérateur
     • N’utilisez jamais votre émetteur ou votre véhicule sous                 plein gaz jusqu´à ce que l´eau soit retirée.
       un orage.
     • N’utilisez JAMAIS votre véhicule où il pourrait entrer en
       contact avec de l’eau salée (Eau de mer ou flaque d’eau

OM                                                                     7                                   WWW.ARRMA-RC.COM
Support
               At ARRMA we want you to love running your kit and make owning a high performance RC car as simple as pos-
               sible. If you have any questions about running, maintaining, tuning or repairing your ARRMA product there are three
options for you to use to get help and advice. Visit ARRMA-RC.com for support, parts and upgrades for your kit. If you can’t find
what you’re looking for then you can always email us at support USA@ARRMA-RC (USA) or support@ARRMA-RC.com (ROW)
24hrs a day and we will do our best to help you with your query.

               Hilfestellung
              Bei ARRMA möchten wir, dass Sie lange Freude an Ihrem High-Performance-RC-Modell haben. Sollten Sie Fragen
             zu Betrieb, Wartung, Tuning oder Reparatur haben, dann bieten wir eine Fülle von Möglichkeiten. Gehen Sie auf
    arrma-rc.com, um mehr über Hilfestellung, Teile oder Tuningteile zu erfahren. Sollten Sie einmal keine Antworten finden, dann
kontaktieren Sie uns über supportUSA@ARRMA-RC (USA) oder support@arrma-rc.com (ROW) und wir werden alles tun, um
Ihnen helfen zu können.`

                Support
                Chez ARRMA notre volonté est que vous appréciez faire évoluer votre voiture et vous faire posséder une modèle
               RC de haute performance aussi simple que possible. Si vous avez des questions concernant le fonctionnement,
la maintenance, le réglage ou la réparation de votre produit ARRMA, il y a trois possibilité que vous pouvez utilisez pour obtenir
l’aide et des conseils. Visitez ARRMA-RC.com pour la prise en charge, des pièces et des mises à niveau de votre kit. Si vous ne
trouvez pas ce que vous recherchez, vous pouvez toujours nous contacter par courriel à supportUSA@ARRMA-RC (USA) ou
support@arrma-rc.com (ROW) 24h par jour et nous ferons de notre mieux pour vous aider dansvotre requête.

                                                                   8                                      WWW.ARRMA-RC.COM
Contents
                     Quick Start Guide                                             10
                     How to Drive                                                  12
                     Electronic Speed Controller (ESC)                             15
                     Radio Gear                                                    17
                     Troubleshooting                                               20
                     Warranty Information                                          46

                Inhalt
                     Schnellstartanleitung                                         22
                     Wie man fährt                                                 24
                     Fahrtregler                                                   27
                     Fernsteuer                                                    29
                     Fehlerbehebung                                                32
                     Garantieinformationen                                         48

                Contenu
                     Guide de Démarrage Rapide                                     34
                     Comment conduire                                              36
                     Variateur électronique                                        39
                     Ensemble radio                                                41
                     Dépannage                                                     44
                     Informations de garantie                                      50

                      Components Komponenten
                         Contenu de la boîte
     •   ARRMA Granite™ 3S (ARA4302V3T1/T2)                  • ARRMA BLX100 ESC (AR390069)
     •   ARRMA Senton™ 3S (ARA4303V3T1/T2)                   • Spektrum™ 3660 3200KV Motor
     •   ARRMA Big Rock™ 3S (ARA4312V3)                        (SPMXSM2000)
     •   ARRMA Typhon™ 3S (ARA4306V3)                        • Spektrum™ 7KG, Metal Gear Servo, 23T
     •           Support
         Spektrum™ 2.4GHz Transmitter (SPMSLT300)              (SPM651)
     •   Spektrum™ 2.4GHz Receiver (SPMSLR300)

OM                                                       9                              WWW.ARRMA-RC.COM
Quick Start Guide

          Remove Body

          Install AA Batteries In Controller
                                                                          4 x AA Batteries
                                                                                (NOT INCLUDED)

                                                                                                         NOTE: Polarity

   CAUTION: Only charge rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury
   to persons and/or damage to property.

   CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

                                                             10                                         WWW.ARRMA-RC.COM
Install Charged Batteries In Car

     Steering Neutral

OM                 11           WWW.ARRMA-RC.COM
How to Drive
                                   ACCELERATE

    LEFT   RIGHT
                           LEFT                   RIGHT

            BRAKE/
            REVERSE
       ACCELERATE

                                                            CO

                                  BRAKE/REVERSE

                      12                 WWW.ARRMA-RC.COM
Connect ESC and Power On

     CONTROLLER ON FIRST        CAR ON SECOND

               ON

                                         ON

           Install Car Body

                    NOW GET
              SHREDDING!
OM                         13         WWW.ARRMA-RC.COM
Power Off

CAR OFF FIRST          CONTROLLER OFF SECOND

                           OFF

            OFF

  Storage

ALL SAFE...
UNTIL NEXT TIME!
                  14             WWW.ARRMA-RC.COM
Electronic Speed Controller (ESC)
                       Only use fully charged LiPo batteries (4.2V per cell) to prevent
                       battery/ESC damage.
ND

                                   Battery Plug

                                                                                             WARNING: Heat sink
                                                                                             may be hot after use.

        Motor wires x 3
                                                                                         Receiver Plug (CH2)

        Power Switch & Set button

                                                  ESC Specifications
       Input Voltage      2S-3S LiPo (7.4-11.1v) 35C 5000mAh Minimum               BEC Output 6.0v/6A Max
                                Req. 6-8 Cell NiMh (7.2v-9.6v)

     Throttle          Connect batteries, turn on TX and press/hold the set button ‘A’. Turn the switch on
     Setup             ‘B’ and release the set button when the RED light flashes on the ESC.

            1. TX in neutral - press set      2. TX full throttle - press set   3. TX full brake - press set
               button (1 Green flash)            button (2 Green flashes)          button (3 Green flashes)

                                                                                                A

                                                                                                               B
                                 4. Switch off ESC to complete setup

OM                                                            15                              WWW.ARRMA-RC.COM
Battery Modes
                 If using LiPo batteries you must set the correct battery mode on the ESC
                 (electronic speed controller) to prevent battery damage.

            Temperature Protection                                                                                       Steerin

            If the ESC temperature exceeds 105 degrees Celsius/221 degrees Fahrenheit, the ESC will
            enter temperature protection mode and the green status LED will blink. Once the ESC has
            cooled down it will resume normal operation after it has been turned off and back on again.

ESC Tuning Options
The ARRMA BLX brushless ESC is setup for use straight from the factory, if you want to alter the                          Pow
settings for your track or driving style please see the table and steps below:
               Variable                         Setting > 1     2         3          4        5         6         7
        1      Low Voltage Cut-Off Threshold
                                                   LIPO        NIMH

        2      Punch Setting
                                                  Level 1     Level 2   Level 3   Level 4   Level 5

        3      Brake Strength
                                                   25%        37.5%      50%      62.5%      75%       87.5%    100%

        4      Running Mode
                                                Fwd/Brk/Rev   Fwd/Brk

        5      Motor Rotation                     Normal      Reverse
                                                  (CCW)        (CW)

To alter ESC settings

                  A

                                  B
            1. Connect a battery. Press and      2. Keep holding the set button      3. To enter the selected
            hold the set button and turn on      and you will see the GREEN          variable, release the set button
            ESC. The RED LED will flash.         LED flash/beep (the number of       on the desired number of
                                                 green flashes represents the        flashes/beeps.
                                                 variable number).

            4. Using the tuning chart, press    5. To save the setting,
            the ‘set’ button until the number   switch the ESC off. Restart
            of red LED flashes and short        the process to make more
            beeps equals the required value.    changes.

Factory Reset
To reset the ESC to factory default settings, connect a battery, turn the transmitter on and then turn
the car on. Press and hold the set button for 4 seconds and release. The Red and Green lights will
flash simultaneously to show you have reset. Switch the ESC off and factory reset is complete.

                                                               16                                     WWW.ARRMA-RC.COM
Radio Gear

     Steering dual rate
                Throttle trim
                                                        SLT3 3CH                        Throttle Limiter
                           Steering trim                                                          Throttle reverse
                                                                                                            Steering reverse

      Power LED
                                                                                                                            Power switch

                                                  Steer        Throttle trigger
                                                wheel (CH1)        (CH2)

                                                    ®

              Battery compartment
                                                              Antenna                            TH               ST
                                                                                             N        R     N          R

                                                                                 CH3 socket
                                                                                        TH TRIM                   ST TRIM

                                                                           Throttle socket  (CH2)
                                                                                        TH RATE
                                                                                                TH LIM
                                                                                                       ST RATE

                                                                                                      50/75/100

                                                                           Steering (CH1) socket

                                                                                Bind socket

       Steering Trim                                              ST Rate

      Throttle Trim                                               Battery Status

      Throttle Trim: factory default neutral,                     If battery status LED is flashing, the
      adjustment is not necessary.                                batteries need to be replaced.

OM                                                              17                                                 WWW.ARRMA-RC.COM
Factory Defaults

Binding

                                                                        ON
          Bind socket

      Insert the Bind Plug in the     Connect a fully charged battery   Power on the ESC. The red
      BIND port on the receiver.           pack to the ESC.             LED flashes, indicating the
                                                                         receiver is in bind mode.

     Center the ST TRIM and TH          Power the transmitter on.       The receiver LED will stop
     TRIM dials on the transmitter.                                             flashing.

          OFF
      Remove the Bind Plug, then         Power off the transmitter.
     power off the ESC to save the
                settings.

                                                    18                          WWW.ARRMA-RC.COM
FCC ID: BRWSPMSLT300; BRWSPMSLR300
                    This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
                    (1) This device may not cause harmful interference, and (2) this device must accept any interference
                    received, including interference that may cause undesired operation.

     CAUTION: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
     UNAUTHORISED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S
     AUTHORITY TO OPERATE THE EQUIPMENT.

     NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
     part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
     a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
     and used in accordance with the instructions, may cause harmful interference to radio communications. However,
     there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
     interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
     encouraged to try to correct the interference by one or more of the following measures:

     •               Reorient or relocate the receiving antenna.
     •               Increase the separation between the equipment and receiver.
     •               Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
     •               Consult the dealer or an experienced radio/TV technician for help.

     Approved under the verification provision of FCC Part 15 as a Class B Digital Device.

     This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This
     equipment should be installed and operated with minimum distance 5mm between the radiator and your body. This
     transmitter must not be co-located or operating in conjunction with any other antenna or transmitter

     Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to oper-
     ate this device.

                     Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: European Union Restriction of Hazard-
                     ous Substances Recast (RoHS2) Directive 2011/65/EU; European Union Registration, Evaluation, Authorization and Restriction of
                     Chemicals (REACH) Directive 1907/2006 European Radio Equipment Directive (RED) 2014/53/EU

     A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

                     Frequency Band: 2405-2474 MHz
                     Max EIRP: 8.30 dBm

         Industry Canada Notice: IC: 6157A-SPMSLT300; 6157A-SPMSLR300
         CAN ICES-3 (B)/NMB-3(B)
         This device complies with Industry Canada license-exempt RSS standard(s). 1. Operation is subject to the following two conditions: (1) this device
         may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the
         device. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
         equipment.

         This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
         and operated with minimum distance 5mm between the radiator and your body. This transmitter must not be co-located or operating in conjunction
         with any other antenna or transmitter

                        INSTRUCTIONS FOR DISPOSAL OF WASTE EQUIPMENT BY PRIVATE USERS IN THE EUROPEAN UNION: This symbol
                        on the product or its packaging indicates this product must not be disposed of with other household waste. Instead, it is the
                        user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of
                        waster electrical and electronic equipment. The separate collection and recycling of your waste equipment at time of disposal will
                        help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.
                        For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your
                        household waste disposal service or location where you purchased the product.

OM                                                                              19                                        WWW.ARRMA-RC.COM
Troubleshooting

Problem            Possible Cause                                          Solution
                                                                           Check transmitter batteries and refit -
                    Batteries are incorrectly installed in transmitter
                                                                           see model/transmitter manual

                    Weak, damaged or no drive battery in model             Install fresh, charged batteries

                                                                           Check condition, reconnect and
                    Frayed or broken motor or ESC wires
                                                                           insulate

                                                                           Stop driving and allow ESC or motor
                    ESC has shut down due to overheating
                                                                           to cool down
Vehicle does not
move                                                                       Replace with new unit - visit ARRMA-
                    Electric motor is damaged
                                                                           RC.com for advice and upgrades!

                                                                           Replace with new unit - visit ARRMA-
                    Waterproof ESC is damaged
                                                                           RC.com for advice and upgrades!

                                                                           Check components and replace -
                    Possible damage to transmission/drive-line
                                                                           visit ARRMA-RC.com for advice

                    ESC low voltage cutoff has activated to protect        Remove drive battery, leave to cool
                    batteries                                              down if necessary, and re-charge

Vehicle does not                                                           Replace with new unit - visit ARRMA-
                    Waterproof ESC is damaged
reverse                                                                    RC.com for advice and upgrades

                                                                           Throttle trim needs to be set to zero/
                    Transmitter throttle trim incorrectly set              neutral - see model/transmitter
Vehicle drives                                                             manual
without input
                    Neutral throttle position of ESC Unit incorrect        Re calibrate the ESC

                    Battery damaged or not fully charged                   Check condition, replace or recharge

                                                                           Clean, check condition and/or replace
                    Electric motor dirty or damaged                        - visit ARRMA-RC.com for more
Short runtime                                                              information

                    Incorrect ESC battery mode - voltage cutoff too high
                                                                           Adjust the battery mode of the unit
                    for the battery you are using

                    Battery damaged or not fully charged                   Check condition, replace or recharge

                                                                           Throttle trim needs to be set to zero/
                    Transmitter throttle trim incorrectly set              neutral - see model/transmitter
                                                                           manual
Sluggish
                                                                           Clean, check condition and/or replace
performance
                    Electric motor dirty or damaged                        - visit ARRMA-RC.com for more
                                                                           information

                                                                           Clean, check condition and/or replace
                    Drivetrain dirty or damaged                            - visit ARRMA-RC.com for more
                                                                           information

                                                           20                             WWW.ARRMA-RC.COM
Check transmitter batteries and refit -
                          Transmitter batteries are weak or fitted incorrectly
                                                                                 see model/transmitter manual
     No control of
                          Servo wires to receiver loose or connected incor-
     vehicle or short                                                            Reinstall signal wires to receiver
                          rectly
     range
                          Transmitter and receiver unit are not 'bound' cor-     Transmitter and receiver need to be
                          rectly                                                 bound - see model/transmitter manual

                                                                                 Stop driving and allow ESC or motor
                          ESC has shut down due to overheating
                                                                                 to cool down
     Steering/Throttle
     operation
                                                                                 Check for sources of interference
     intermittent         Transmitter and receiver unit are not 'bound' cor-
                                                                                 and re-bind transmitter/receiver - see
                          rectly
                                                                                 transmitter manual

                                                                                 Adjust steering trim - see model/
                          Steering trim setting out
                                                                                 transmitter manual

     Vehicle wanders                                                             Check components and replace - visit
                          Damaged steering components
     left/right without                                                          ARRMA-RC.com for advice
     steering input
                                                                                 Clean, check condition and/or replace
                          Drivetrain dirty or damaged                            - visit ARRMA-RC.com for more
                                                                                 information

                                                                                 Reverse relevant channel on trans-
                          Relevant channel of transmitter is reversed            mitter - see model/
                                                                                 transmitter manual
     Steering/Throttle
     operation
                                                                                 Reconnect in the correct orientation
     Reversed
                          Check that the wires from the ESC to the motor are     (orange to orange, yellow to yellow
                          connected correctly                                    and blue to blue) ensuring fit is tight; if
                                                                                 not pinch female connector with pliers

                                                                                 Adjust transmitter dual-rate - see
                          Transmitter steering dual-rate set incorrectly
                                                                                 transmitter manual
     Limited steering
     angle
                                                                                 Check components and replace - visit
                          Damaged steering components
                                                                                 ARRMA-RC.com for advice

OM                                                            21                               WWW.ARRMA-RC.COM
Schnellstartanleitung
          Entfernen Sie die Karosserie

          Legen Sie die AA Batterien in das Steuergerät ein

                                                                   4x AA Batterien
                                                                (Nicht im Lieferumfang enthalten)

                                                                                               Wichtig: beachten
                                                                                                Sie die Polung

   Vorsicht: Wenn Sie Akkus verwenden, laden Sie nur Akkus auf. Das Aufladen von Akkus, die nicht wiederaufladbar sind, kann
   dazu führen, dass die Batterien platzen, was zu Verletzungen von Personen und Personen oder Sachschäden führt.

   Vorsicht: Explosionsgefahr, wenn die Batterie durch einen falschen Typ ersetzt wird. Aussetzen von gebrauchten Batterien nach
   nationalen Vorschriften.

                                                         22                                         WWW.ARRMA-RC.COM
Setzen Sie den geladenen Akku in das Fahrzeug ein

     Lenkung Neutralposition

OM                       23                WWW.ARRMA-RC.COM
Wie man fährt
                                     Beschleunigung

   Links   Rechts
                             Links                    Rechts

                 Bremsen/
                 Rückwärts

      Beschleunigung

                                                                 Fern

                                       Bremsen/
                                       Rückwärts

                        24                    WWW.ARRMA-RC.COM
ESC Verbindung und Strom anschalten

     Fernsteuerung als erstes einschalten        Fahrzeug als zweites einschalten

             AN

                                                                     AN

                 Karosserie befestigen

                    Nun kann es losgehen!
OM                                          25                   WWW.ARRMA-RC.COM
Ausschalten

Fahrzeug als erstes ausschalten        Fernsteuerung als zweites
                                             ausschalten

                                          AUS
                        AUS

         Lagern

Alles sicher verstaut...
bis zum nächsten Mal!
                                  26                  WWW.ARRMA-RC.COM
Fahrtregler
                       Benutzen Sie nur vollständig geladene LiPo-Akkus (4,2V pro
                       Zelle), um Schäden am Akku/Regler zu vermeiden.

                                     Akkustecker

                                                                                            WARNUNG: Der
                                                                                            kühlkörper kann nach
                                                                                            der fahrt heiss sein

          Motorkabel x 3
                                                                                       Empfängerkabel (CH2)

             Ein/Aus-Schalter & Set-
                     Knopf
                                               Reglerspezifikationen
     Eingangsspan-       2S-3S LiPo (7.4-11.1v) 35C 5000mAh Minimum        BEC Ausgang           6.0v/6A Max
         nung                  Req. 6-8 Cell NiMh (7.2v-9.6v)

     Gaseinstellung Verbinden Sie den Akku, schalten Sie den Sender ein und drücken/halten Sie den Set-
                            Knopf “A”. Stellen Sie den Knopf auf “B” und lassen Sie den Set-Knopf los, wenn die
                            ROTE LED des Reglers zu blinken beginnt.

             1. Sender in Neutralposition    2. Sender auf Vollgas -          3. Sender auf Vollbremse
                - drückenSie den Knopf (1       drücken Sie den Knopf (2         - drücken Sie den Knopf (3
                grünes Blinksignal)             grüne Blinksignale)              grüne Blinksignale)

                                                                                             A

                                                                                                          B
                     4. Schalten Sie den Regler aus, um das Setup abzuschließen

OM                                                        27                               WWW.ARRMA-RC.COM
Batteriemodus
                  Wenn Sie LiPo-Akkus verwenden, muss der entsprechende Batteriemodus am Fahrtregler
                  angewählt sein, um Schäden an der Batterie durch Tiefentladung zu verhindern.
             Temperatursicherung                                                                                         Lenkun
             Wenn die Temperatur des Reglers 105 Grad Celsius übersteigt, geht der Regler in den                              R
             Übertemperatur-Schutzmodus und die Grün LED wird blinken. Nachdem die Temperatur
             des Reglers auf ein normales Maß gesunken ist, wird er wieder normal funktionieren.
Reglerabstimmung
 Der ARRMA BLX Brushless-Regler ist werkseingestellt, kann aber individuell auf die eigenen
 Bedürfnisse abgestimmt werden. Wie genau, das erfahren Sie weiter unten:
                Variable                      Setting > 1     2         3          4          5         6        7
         1      Unterspannungsabschaltung
                                                 LIPO        NIMH
                                                                                                                          Pow
         2      Punch-Einstellung
                                                Level 1     Level 2   Level 3   Level 4     Level 5

         3      Bremskraft
                                                 25%        37.5%      50%      62.5%        75%       87.5%   100%

         4      Fahrmodus
                                              Fwd/Brk/Rev   Fwd/Brk

         5      Motordreh                       Normal      Reverse
                                                (CCW)        (CW)

ESC-Einstellungen ändern

                   A

                                    B
             1. Verbinden Sie den Akku.         2. Halten Sie den Knopf                3. Um das entsprechende
             Drücken und halten Sie den         gedrückt und die grüne LED             Parameter zu ändern,
             Set-Knopf und schalten Sie         wird blinken, es werden                lassen Sie den Knopf bei der
             den Regler ein. Die rote LED       Pieptöne zu hören sein                 entsprechenden Anzahl an
             wird blinken.                      (die Anzahl der grünen                 Blinksignalen los.
                                                Blinksignale zeigt das
                                                einzustellende Parameter)

         4. Mithilfe der Abstimmungstabelle       5. Um die Einstellung zu
         können Sie das Parameter               speichern, schalten Sie den
                                               Regler aus. Beginnen Sie den
         ändern, indem Sie den Set-Knopf         Prozess von neuem, wenn
         so oft drücken wie gewünscht. Die     Sie weitere Werte verändern
         rote LED und eine entsprechende                 möchten.
         Anzahl an Pieptönen zeigen den
         eingestellten Wert.

 Werks
 Um den Regler in die Werkseinstellung zu versetzen, stecken Sie einen Akku an, schalten Sie den Sender sowie das
 Fahrzeug ein. Drücken und halten Sie den Set-Knopf für 4 Sekunden und lassen Sie ihn danach los. Die rote und
 grüne LED werden gleichzeitig blinken, um den erfolgreichen Reset anzuzeigen. Schalten Sie den Regler aus und die
 Werkseinstellung ist wiederhergestellt.

                                                              28                                      WWW.ARRMA-RC.COM
Fernsteuer

     Lenkungs-Dual-
          Rate
                Gastrimmung
                                                       SLT3 3CH                         Gaslimiter
                       Lenkungstrimmung
                                                                                                             Gas-Reverse
                                                                                                                    Lenkungs-Reverse

      Power LED
                                                                                                                          An/Ausschalter

                                               Lenkrad (CH1)   Gashebel (CH2)

                                                   ®

                   Batteriefach
                                                                                               TH               ST

                                                          Antenne                          N        R     N          R

                                                                                          TH TRIM               ST TRIM
                                                                        Kanal 3 (CH3)
                                                                          Buchse
                                                                                          TH RATE               ST RATE
                                                                                                    TH LIM

                                                                       Gasbuchse (CH2)              50/75/100

                                                                       Lenkungsbuchse (CH1)

                                                                          Socket binden

      Lenkungstrimmung                                               ST Rate

       Gastrimmung                                                   Batterie-Status

       Gastrimmung: Werkseinstellung                                Wenn die Batterie-Status-LED blinkt,
       null, Einstellung nicht erforderlich.                        müssen die Batterien des Senders
                                                                    erneuert werden.

OM                                                              29                                               WWW.ARRMA-RC.COM
Werkseinstellungen

Verbinden

                                                                            AN
          Bind socket

   Stellen Sie das Fahrzeug auf einen   Schließen Sie einen vollständig   Schalten Sie den Regler ein. Die rot
   ebenen Untergrund und stecken Sie    geladenen Akku an den Regler      LED blinkt, und zeigt damit an, dass
   den Bindestecker in den BIND Port                 an.                   sich der Empfänger im Bindemode
            des Empfängers.                                                             befindet.

       Zentrieren Sie die ST Trim       Schalten Sie den Sender ein.         Die Empfänger-LED hört auf
      und TH Trim Regler auf dem                                                    zu blinken.
                Sender.

           AUS
   Entfernen Sie den Bindestecker und   Schalten Sie den Sender aus.
  schalten dann den Empfänger aus um
     die Einstellungen zu speichern.

                                                      30                              WWW.ARRMA-RC.COM
EU Konformitätserklärung: Horizon LLC erklärt hiermit, dass dieses Produkt konform zu den essentiellen Anforderungen der RED und EMC
     Direktive ist.
     Eine Kopie der Konformitätserklärung ist online unter folgender Adresse verfügbar : http://www.horizonhobby.com/content/support-
     render-compliance.

         ENTSORGUNG IN DER EUROPÄISCHENUNION: Dieses Produkt darf nicht über den Hausmüll entsorgt werden. Es ist die
         Verantwortung des Benutzers, dass Produkt an einer registrierten Sammelstelle für Elektroschrott abzugeben diese Verfahren
         stellt sicher, dass die Umwelt geschont wird und natürliche Ressourcen nicht über die Gebühr beansprucht werden. Dadurch
         wird das Wohlergehen der menschlichen Gemeinschaft geschützt. Für weitere Informationen, wo der Elektromüll entsorgt
         werden kann, können Sie Ihr Stadtbüro oder Ihren lokalen Entsorger kontaktieren.

OM                                                             31                                      WWW.ARRMA-RC.COM
Fehlerbehebung

Problem                Mögliche Ursache                                          Lösung
                                                                                 Überprüfen Sie die Batterien in der
                       Batterien wurden in der Funkfernsteuerung nicht korrekt
                                                                                 Fernsteuerung und setzten Sie sie ggf.
                       eingelegt
                                                                                 neu ein (siehe Bedienungsanleitung)

                                                                                 Installieren Sie ein neuen, voll
                       Schwacher oder beschädigter Akku im Fahrzeug
                                                                                 aufgeladenen Akku

                                                                                 Überprüfen Sie den Zustand, verbinden
                       Zerschlissene oder beschädigte Motor- oder ESC Kabel      Sie Kabel erneut und isolieren Sie sie
                                                                                 entsprechend

                                                                                 Halten Sie das Fahrzeug an und geben
                       ESC wurde durch Überhitzung abgeschaltet                  Sie dem Motor / Einheit die Möglichkeit
                                                                                 abzukühlen
Fahrzeug bewegt
sich nicht                                                                       Tauschen Sie ihn mit einem neuen Motor
                       Elektromotor ist beschädigt                               aus – besuchen Sie ARRMA-RC.com für
                                                                                 Ratschläge und die neuesten Upgrades!

                                                                                 Tauschen Sie ihn mit einem neuen Gerät
                       Wasserdichter ESC Regler ist beschädigt                   aus – besuchen Sie ARRMA-RC.com für
                                                                                 Ratschläge und die neuesten Upgrades!

                                                                                 Überprüfen Sie die Bauteile und
                                                                                 tauschen Sie sie ggf. Aus – besuchen
                       Möglicher Schaden beim Getriebe / Antriebssystem
                                                                                 Sie ARRMA-RC.com für Ratschläge und
                                                                                 Hilfestellungen

                       Die Spannungsunterbrechnung beim ESC Regler wurde         Entfernen Sie Batterie, lassen Sie sie
                       aktiviert um die Batterien zu schützen                    ggf. abkühlen und laden Sie sie neu

                                                                                 Tauschen Sie ihn gegen ein neues Gerät
Fahrzeug fährt nicht
                       Wasserdichter ESC Regler ist beschädigt                   aus – besuchen Sie ARRMA-RC.com für
rückwärts
                                                                                 Ratschläge und die neuesten Upgrades!

                                                                                 Trimmhebel muss in der Null/
                       Der Trimmhebel beim Gas wurde bei der
                                                                                 Neutral Position stehen (siehe
Fahrzeug fährt         Funkfernsteuerung inkorrekt eingestellt
                                                                                 Bedienungsanleitung)
selbstständig
                       Die Neutralposition der Einheit ist inkorrekt             Kalibrieren Sie den ESC

                                                                                 Überprüfen Sie den Zustand des Akkus,
                       Akku beschädigt oder nicht vollständig geladen            tauschen Sie ihn aus oder laden Sie ihn
                                                                                 vollständig

                                                                                 Säubern Sie den Motor, überprüfen Sie
Short runtime                                                                    seinen Zustand und/oder tauschen Sie ihn
                       Elektromotor verschmutzt oder beschädigt
                                                                                 aus – besuchen Sie ARRMA-RC.com für
                                                                                 weitere Informationen

                       Inkorrekter ESC Akkumodus (Spannungsunterbrechnung        Passen Sie den entsprechenden
                       zu hoch angesetzt für die aktuell benutzten Akkus)        Akkumodus bei der Einheit an

                                                                32                               WWW.ARRMA-RC.COM
Überprüfen Sie den Zustand des Akkus,
                         Akku beschädigt oder nicht vollständig geladen              tauschen Sie ihn aus oder laden Sie ihn
                                                                                     vollständig

                                                                                     Trimmhebel muss in der Null/
                         Inkorrekte Einstellung beim Trimmhebel                      Neutral Position stehen (siehe
                                                                                     Bedienungsanleitung)
     Schleppende
                                                                                     Säubern Sie den Motor, überprüfen Sie
     Leistung
                                                                                     seinen Zustand und/oder tauschen Sie ihn
                         Elektromotor verschmutzt oder beschädigt
                                                                                     aus – besuchen Sie ARRMA-RC.com für
                                                                                     weitere Informationen

                                                                                     Säubern Sie den Antriebsstrang,
                                                                                     überprüfen Sie seinen Zustand und/oder
                         Antriebsstrang verschmutzt oder beschädigt
                                                                                     tauschen Sie ihn aus – besuchen Sie
                                                                                     ARRMA-RC.com für weitere Informationen

                                                                                     Überprüfen Sie die Batterien im
                         Die Batterien im Funkgerät sind zu schwach oder wurden      Funkgerät, tauschen Sie sie aus
                         falsch eingesetzt                                           oder setzen Sie sie korrekt ein (siehe
                                                                                     Bedienungsanleitung)
     Keine Kontrolle
     über das Fahrzeug
                                                                                     Installieren Sie die Signaldrähte zur
     bzw. kurze          Servokabel zur Einheit sind lose oder inkorrekt verbunden
                                                                                     Einheit erneut
     Reichweite
                                                                                     Das Funkgerät und Empfänger müssen
                         ARRMA Funkfernsteuerung und Einheit sind nicht korrekt
                                                                                     korrekt miteinander verbunden sein –
                         miteinander verbunden
                                                                                     siehe Bedienungsanleitung

                                                                                     Halten Sie das Fahrzeug an und geben
                         Einheit wurde aufgrund Überhitzung ausgeschaltet            Sie dem Motor / Einheit die Möglichkeit
                                                                                     abzukühlen
     Lenkung /
     Gashebelnutzung
                                                                                     Überprüfen Sie die möglichen
     unterbrochen /
                                                                                     Ursachen der Störung und stellen Sie
     unregelmässig       ARRMA Funkfernsteuerung und Einheit sind nicht korrekt
                                                                                     eine erneute Verbindung zwischen
                         miteinander verbunden
                                                                                     Fernsteuerung und Empfänger her (siehe
                                                                                     Bedienungsanleitung)

                                                                                     Stellen Sie die Lenkung am Trimmhebel
                         Trimmhebel der Lenkung ist nicht korrekt eingestellt
                                                                                     korrekt ein (siehe Bedienungsanleitung)

                                                                                     Überprüfen Sie die Lenkbauteile und
                                                                                     tauschen Sie sie ggf. aus – besuchen Sie
     Fahrzeug driftet    Beschädigte Lenkbauteile
                                                                                     ARRMA-RC.com für weitere Informationen
     eigenständig nach
                                                                                     und Hilfestellungen
     rechts/links
                                                                                     Säubern Sie den Antriebsstrang,
                                                                                     überprüfen Sie seinen Zustand und/oder
                         Antriebsstrang verschmutzt oder beschädigt
                                                                                     tauschen Sie ihn aus – besuchen Sie
                                                                                     ARRMA-RC.com für weitere Informationen

                                                                                     Wählen Sie den entsprechenden
                         Der entsprechende Kanal an der Funkfernsteuerung ist
                                                                                     Kanal an der Fernsteuerung (siehe
                         umgekehrt
                                                                                     Bedienungsanleitung)
     Lenkung/Gas
     funktionieren                                                                   Verbinden Sie die Kabel in der korrekten
     verkehrt herum                                                                  Vorgabe (Orange bis Orange, Gelb bis
                         Überprüfen Sie das die Kabel vom ESC Regler zum Motor
                                                                                     Gelb und Blau bis Blau). Stellen Sie
                         korrekt verbunden sind
                                                                                     sicher dass die Verbinder fest sitzen (die
                                                                                     Buchsen ggf. mit einer Zange befestigen)

                                                                                     Stellen Sie die Doppellenkung an
                         Die Doppellenkung an der Funkfernsteuerung ist inkorrekt
                                                                                     der Fernsteuerung korrekt ein (siehe
                         eingestellt
                                                                                     Bedienungsanleitung)
     Limitierter Lenk-
     winkel                                                                          Überprüfen Sie die Lenkbauteile und
                                                                                     tauschen Sie sie ggf. aus – besuchen Sie
                         Beschädigte Lenkbauteile
                                                                                     ARRMA-RC.com für weitere Informationen
                                                                                     und Hilfestellungen

OM                                                              33                                   WWW.ARRMA-RC.COM
You can also read