Aria Jellyfish A.JF - PLH Italia
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
Aria Jellyfish
A.JF
PLH Aria Jellyfish cod. A.JF
Bluetooth controllable, Casambi enabled, 4 input 4 output interface, with feedback led and multivoltage power supply. It can be
connected, only by qualified professionals. Can be controlled via PLH Aria keypads, and with Casambi app available for iOs (iPhone 4S
or later, iPad 3 or later, iPod Touch 5th gen or later) and Android devices (Android 4.4 KitKat or later devices produced after 2013 with
full Bluetooth 4.0 support).
Drawings and measures
Technical specifications
Electrical input specs Firmware:
Voltage range and frequency AC | DC: 90 - 250V (0,5 VA) | 12-30V DC (1W) 5081 Output: 4 Switch (relais bistable) -
0 Push button (relais monostable)
Input: 4 dry contact
Input
Dry contact 4 NO to ground and pass through 5082 Output: 3 Switch (relais bistable) -
1 Push button (relais monostable)
Output Input: 4 dry contact
Transistor 4 (100mA and 30V DC max); open-collector
to ground; control of inductive load allowed 5083 Output: 2 Switch (relais bistable) -
(with relays) 2 Push button (relais monostable)
Input: 4 dry contact
Feedback
5084 Output: 1 Switch (relais bistable) -
Led white (output) and blue (input) on board
3 Push button (relais monostable)
Input: 4 dry contact
Radio transceiver
Maximum output power: 2,4...2,483 Ghz +4 dBm 5085 Output: 0 Switch (relais bistable) -
Ambient temperature, ta: -20...+45 °C 4 Push button (relais monostable)
Max. case temperature, tc: +65 °C Input: 4 dry contact
Max. relative humidity: 0...80%, non-cond.
Range (depending on the surrondings) up to 15 m 5975 Output: 4 Pwm Input: 4 dry
contact
Wiring
Wire range, solid & stranded: interface si provided with precutted 5 cm
wires 0,5 mm2 16 AWG
Mechanical data
Dimensions: 50,0 x 50,0 x 40,0 mm
Weight: 50 g
Degree of protection: IP67
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Installation
Make sure that the mains voltage is switched off when making any connections. Use right connectors or seal butt slice to join the jellyfish interface to the
electric wires of the plant..
If you install the interface into a heat sensitive environment (i.e. inside a luminaire or in a ceiling outlet box above a luminaire), make sure that the ambient
temperature does not exceed the specified maximum value.
Wiring
Insulate the not used wires. Use the right connectors for the connections, not included, like Perma-Seal Butt Slice (Molex 19164-0013) or Wago 221, 243 or
2273 series.
Common (-) 3a 4a Common (-)
Output 4 3b 4b Input 4
Output 3 3c 4c Input 3
Output 2 3d 4d Input 2
Output 1 3e 4e Input 1
Common (+) 3f
Input 1 2a
Input 2 2b
Input 3 2c
Input 4 2d
Common (-) 2e
90-250V AC Neutral 1a
90-250V AC Phase 1b Perma-Seal Butt Slice
Molex
6a Max 30V DC (+)
6b Max 30V DC (-)
Wago 221
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Example 1: connection with BUS dry contact interface Gira 1119 00 Konnex interface
In this solution you can control directly, using a PLH Aria keypad or a smartphone, a KNX bus system via a bus dry contact interface. Power supply need to be
granted (230V AC or maximum 30V DC using the right wires)
Refer to Gira Interface specification document for any further information
http://download.gira.com/data3/11193290.pdf
Firmware 5085 PLH Jellyfish
A1/E1
A2/E2
com
E3
E4
- +
GN
RD
GY
PK
YE
KNX Bus
90-250V AC Neutral 1a
90-250V AC Phase 1b
6a Max 30V DC (+)
6b Max 30V DC (-)
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Example 2: connection with BUS dry contact interface Philips LCU2070 DALI interface
In this solution you can control directly, using a PLH Aria keypad or a smartphone, a Dali bus system via a bus dry contact interface. Power supply need to be
granted (230V AC or maximum 30V DC using the right wires)
Refer to Philips Interface specification document for any further information
http://www.assets.lighting.philips.com/is/content/PhilipsLighting/a7f5741c4ff54b2c90e4a68f00b8c881
Firmware 5085 PLH Jellyfish
DA+
DA - DALI Bus
1
LCU2070/00 2
9137 003 35103 3
4
Made in E.U. 5
PFT yyww 6
90-250V AC Neutral 1a
90-250V AC Phase 1b
6a Max 30V DC (+)
6b Max 30V DC (-)
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Example 3: connection with BUS dry contact interface C2N-UNI8IO Crestron interface
In this solution you can control directly, using a PLH Aria keypad or a smartphone, a Cresnet bus system via a dry contact interface. Power supply need to be
granted (230V AC or maximum 30V DC using the right wires)
Refer to Crestron Interface specification document for any further information
https://www.crestron.com/getmedia/41ce847e-5535-492f-a1df-298812b77537/ss_c2n-uni8io_1
Firmware 5085 PLH Jellyfish
5V 1 2 3 4 5 6 7 8 24V
GG 1 2 3 4 5 6 7 8
OUTPUT
INPUT
Cresnet Bus
90-250V AC Neutral 1a
90-250V AC Phase 1b
6a Max 30V DC (+)
6b Max 30V DC (-)
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Example 4: connection with BUS dry contact interface QSE-CI-WCI Lutron interface
In this solution you can control directly, using a PLH Aria keypad or a smartphone, a Lutron bus system via a dry contact interface. Power supply need to be
granted (230V AC or maximum 30V DC using the right wires)
Refer to Lutron Interface specification document for any further information
http://www.lutron.com/TechnicalDocumentLibrary/369681a.pdf
Firmware 5085 PLH Jellyfish
QS LINK wiring
12345678
LEDs
Contact Closure Inputs
2 (Orange)
3 (Yellow )
6 (Purple)
4 (Green)
9 (Blac k )
7 (Gray)
5 (Blue)
1 (Red)
8
90-250V AC Neutral 1a
90-250V AC Phase 1b
6a Max 30V DC (+)
6b Max 30V DC (-)
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Example 5: connection with relays bistable
In this solution you can control directly, using a PLH Aria keypad or a smartphone or a local normally open push buttons (4 in this scheme), relays with coil in
extra low tension and contact in 230V (for example Finder 46 series) and 24 V leds. Power supply need to be granted (230V AC or maximum 30V DC using
the right wires)
Firmware 5083
k1 k2
230V AC Neutral 1a
230V AC Phase 1b
6a 24V DC (+)
6b 24V DC (-)
230V AC Phase
k1 k2
load load
230V 230V Finder 46 series
230V AC Neutral
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Example 6: control of curtains
In this solution you can control 2 curtain in 230V AC directly, using a PLH Aria keypad or a smartphone or a local normally open push buttons (4 in this
scheme), relays with mechanical interlock with coil in extra low tension and contact in 230V. Power supply need to be granted (230V AC or maximum 30V DC
using the right wires)
Firmware 5085
k1 down k2 up k3 down k4 up
230V AC Neutral 1a
230V AC Phase 1b
6a 24V DC (+)
6b 24V DC (-)
230V AC Phase
M M
1 1
UP DOWN UP DOWN
k2 k4
6 3 6 3 6 3 6 3
k1 k3
5 7 4 2 5 7 4 2 5 7 4 2 5 7 4 2
Finder 46 series
230V AC Neutral
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Example7: control of single channel D-PWM ballast
In this solution you can control, using a PLH Aria keypad or a smartphone, a PWM dimmer led. Power supply need to be granted (230V AC or maximum 30V
DC using the right wires)
Refer to Dalcnet specification document for any further information
http://www.dalcnet.com/wp-content/uploads/DLA1248_1CH_ita.pdf
Firmware 5975 PLH Jellyfish
DC In 12-48V DC (+)
DC In 12-48V DC (-)
LED
90-250V AC Neutral 1a
90-250V AC Phase 1b
6a Max 30V DC (+)
6b Max 30V DC (-)
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0Example8: control of multi channel D-PWM ballast
In this solution you can control, using a PLH Aria keypad or a smartphone, a PWM multi dimmer led. Power supply need to be granted (230V AC or maximum
30V DC using the right wires)
Refer to Dalcnet specification document for any further information
http://www.dalcnet.com/wp-content/uploads/DLA1224_4CH_ita.pdf
Firmware 5975 PLH Jellyfish
IN PWM
LED BOOSTER
DC IN OUT
12-24V DC (+)
SINGLE COLOR LED
12-24V DC (-)
TUNEBLE WHITE
RGBW
RGB
6a Max 30V DC (+)
6b Max 30V DC (-)
90-250V AC Neutral 1a
90-250V AC Phase 1b
Warning!
! Hazardous voltages. Risk of electric shock or fire. Only qualified professionals should make the
connections in accordance with the local regulations and rules. Disconnect the mains power
supply and verify its absence prior to installation.
© 2017 - epic srl - All rights reserved - Subject to technical change - Check periodically the website Doc. DS_A.JF rev. 1.0You can also read
