10G Ethernet SFP+ Transceiver (40 km) - LBB-SFP+ 10G-40CD-55 - Lindsay Broadband
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
10G Ethernet SFP+ Transceiver (40 km)
LBB-SFP+ 10G-40CD-55
Lindsay Broadband's LBB-SFP+ 10G-40CD-55 small form-factor pluggable plus (SFP+) 10G
Ethernet transceiver is intended for 40 km reach service from 8.5 to 10.5 Gbps, 1550 nm, single-
mode high-speed communications equipment where affordability, extraordinary performance,
and reliability are essential. It consumes low power, operates from a 3.3 VDC power supply,
and is offered in the commercial temperature range. The low jitter and low bit error rate optical
assembly features a 1550 nm EML laser transmitter and PIN/TIA receiver. It incorporates the
SFP+ MSA LVTTL Loss of Signal (RX_LOS), TX Fault, MOD_ABS and TX Disable monitor and
LBB-SFP+ 10G-40CD-55
control functions. The differential AC coupled TX and RX data interfaces are CML compatible. (top view)
This SFP meets IEEE 802.3ae 10GBASE-ER/EW, SFF-8431 and SFF-8432 requirements and
is Class I laser safety compliant.
FEATURES
• LC duplex transceiver • High performance 1550 nm EML laser
• Maximum link length of 40 km • High sensitivity PIN/TIA optical receiver
• 8.5 to 10.5 Gbps • Single-mode operation
• Single +3.3 VDC power supply • Case Operating Temperature Range:
Commercial 0°C to +70°C (+32°F to +158°F)
• 2x10 SFP+ MSA compliant package
• RoHS6 compliant
• Hot-swappable
APPLICATION
• 10GBASE-ER/EW 10G Ethernet
PIN ASSIGNMENT
Page 1 of 510G Ethernet SFP+ Transceiver (40 km) LBB-SFP+ 10G-40CD-55
PIN DESCRIPTIONS
Pin # Symbol Description
1 VeeT Transmitter Ground (1)
2 TX Fault Transmitter Fault (2)
3 TX Disable Transmitter Disable. Laser output disabled on high
4 SDA 2-wire Serial Interface Data Line (MOD_DEF2)
5 SCL 2-wire Serial Interface Clock (MOD_DEF1)
6 MOD_ABS Module Absent, connected to VeeT
7 RS0 Rate Select 0: Not used (3)
8 RX_LOS Loss of Signal indication. Logic 0 indicates normal operation (2)
9 RS1 Rate Select 1: Not used (3)
10 VeeR Receiver Ground (1)
11 VeeR Receiver Ground (1)
12 RD- Receiver Inverted DATA output (4)
13 RD+ Receiver Non-inverted DATA output (4)
14 VeeR Receiver Ground (1)
15 VccR Receiver Power Supply (5)
16 VccT Transmitter Power Supply (5)
17 VeeT Transmitter Ground (1)
18 TD+ Transmitter Non-inverted DATA input (6)
19 TD- Transmitter Inverted DATA input (6)
20 VeeT Transmitter Ground (1)
NOTES:
(1) Module ground pins VeeT & VeeR are isolated from the module case & chassis ground within the module
(2) Shall be pulled up with 4.7-10 k ohms to a voltage between 3.15 V & 3.6 V on the host board
(3) The pins are pulled low to VeeT with a > 30 k resistor in the module
(4) The 100 ohm differential RX data output is internally AC coupled & terminated
(5) The power supply pins VccT & VrrT are connected together in the module
(6) The 100 ohm differential TX data input is internally AC coupled & terminated
SPECIFICATIONS
Specifications
Parameter
Min Typ Max
Absolute Maximum Ratings (Exceeding these ratings may cause irreversible damage to the device) (1)
DC Supply Voltage 0V 3.6 V
Storage Temperature -40°C to +85°C (-40°F to +185°F)
Case Operating Temperature Commercial 0°C to +70°C (+32°F to +158°F)
Storage Humidity 0-95%, non-condensing
Operating Humidity 0-85%, non-condensing
Recommended Operating Conditions
Case Operating Temperature Commercial 0°C to +70°C (+32°F to +158°F)
DC Supply Voltage 3.135 V 3.465 V
Module Supply Current 450 mA
Transmitter Electrical Characteristics (TOP = 25°C/177°F, Vcc = 3.3 Volts)
Differential Data Input Swing 180 mV 700 mV
Differential Input Impedance 100 Ω
TX Disable Voltage 2.0 V Vcc
TX Enable Voltage 0V 0.8 V
Page 2 of 510G Ethernet SFP+ Transceiver (40 km) LBB-SFP+ 10G-40CD-55
SPECIFICATIONS CONT'D.
Specifications
Parameter
Min Typ Max
Receiver Electrical Characteristics (TOP = 25°C/177°F, Vcc = 3.3 Volts)
Differential Data Output Swing 300 mV 850 mV
Differential Output Impedance 100 Ω
LOS Assert Voltage 2.4 V Vcc
LOS De-assert Voltage Vee Vee+0.4 V
Transmitter Optical Characteristics (TOP = 25°C/177°F, Vcc = 3.3 Volts)
Laser Type 1550 nm EML laser
Average Output Power 10.3125 Gbps, PRBS 231-1 -4.7 dBm 4 dBm
Average Output Power of OFF TX -30 dBm
Wavelength 1530 nm 1565 nm
Extinction Ratio 10.3125 Gbps, PRBS 231-1 3 dB
10.3125 Gbps, PRBS 231-1,
Dispersion Penalty 3 dB
BER10G Ethernet SFP+ Transceiver (40 km) LBB-SFP+ 10G-40CD-55
FUNCTIONAL SCHEMATIC
MECHANICAL SPECIFICATIONS
Page 4 of 510G Ethernet SFP+ Transceiver (40 km) LBB-SFP+ 10G-40CD-55
ORDERING INFORMATION
Part # Description
LBB-SFP+ 10G-40CD-55 10 Gbps SFP+ optical pluggable transceiver, SM, 1550 nm TX, 40 km, DDM, 0°C to +70°C (+32°F to +158°F), LC duplex connector
2-2035 Fisher Dr, Peterborough, ON K9J 6X6 Canada
+1.705.742.1350 • 1.800.465.7046 • info@lindsaybb.com • lindsaybb.com
© 2021 Lindsay Broadband Inc. All rights reserved. Printed in Canada. Non-Lindsay Broadband product marks, All information is subject to change without notice.
service marks, and company names in this document are the property of their respective owners. Rev. 05/21 (LBB0362) • Page 5 of 5You can also read
